Search results

I'm needing the 2 stainless clips that cover the windshield joints, where the 2 halves come together. On the outside of the windshield, also screws if you have them. Thanks Don 620-617-7473

Thanks TJ I got it out that way but I 'm not sure it is correct. The glass is rectangular shape and you can't turn it or rotate it. I finally bent the bead molding out towards the inside of the car and got it out, pretty tight, not sure I will get it back in. You can't go clear down because it...

was wondering if anyone could tell e how to remove the rear door glass on a 1937 ford 4 door slant back- before I start

So does -BOKC74961- make a good vin. #?? Also would the Kansas City plant be with K C or just K and the other # could be O ?? Thanks for the help

Sorry- it's a 2 dr, the back windows have likea quarter glass in them at the back??

Hello Guys, I have a 50 ford and the vin plate on the firewall is corroide some in the middle- It's B 0 K C( C could be an O) and 7? 4? ( cant read very well pretty sure on these but are they important) 961. It a 2 dr. sedan, vent windows in the back doors, V8, overdrive. I'm getting a...

ttt

I'm pretty new to the fords so I may ask some foolish questions from time to time. I've had an old 36 I bought some time ago, needs complete resto but mostly complete-has engine ****** int,.My question is I recently bought another, driver, and it was missing the thin trim that goes top and sides...

looking for the windshield garnish, inside: good scuff plates:and headliner bows for 1936- 5 window ford coupe

I bought some old stock from a fella whos dad had a hot rod shop. Pretty sure I have an old stock harness. Let me know if your interested. I used one on my 36.

I've had good luck in the past with a product called "silver solder". most auto parts stores have it. Just put it in and drive it a while. Wont hurt the heater cores.

Hello Guys, I'm going to put a 12 volt electric fuel pump on my 37 ford flathead. I know it shouldn't be high pressure I've seen some cheap ones on ebay for lawnmowers and cycles 1-4 lbs. pressure. Do you recon one would work? I'm going to use the mechanical one mostly. This would just be used...

Going to put some old ford wire wheels on my 37 and I keep hearing I need to put adaptors on first, Anybody have an old set they don't use or need? Thanks also would like to find a good used hood latch handle, it has the "V8" embossed in it for a 39 deluxe

Like to find cowl patch panels for my 37 ford slantback. Complete or mabey partially cut? P.M. me thanks

Thanks for all the info. guys, I got a set on the way

I was thinking about installing 2 tempurature gauges in my 37 ford. In hang below cluster Has anybody did this and is it nessary? Also what is the thread size for the sending unit in the head? 3/8 pipe??. Thanks Guys

Thanks Mart, I did mean tie rod, the ends are ok, it's the bar inbetween them one side has a slight curve in it.

A friend and I have pulled the front suspension out from under my 37 ford- install new spring schackels, redo springs and check and re shim spindles. I noticed the tie rod has a small curve at 1 end, the curve would be parell with the road, is it bent or should it be straight, shows no damage...

I would like to find a good front rubber floor mat, back would be ok too. It's for my old beatter 1937 ford slantback, and I realy don't want new but may end up that way if I don't hear from someone soon who mabey up graded theirs to carpet. Please no rotted out ones, I have one of them. Thanks...

Thanks for the advice Guys, I have them done now and used the slip spray, waiting on new bushings and I'll get it back under her.