Search results

  1. johncusano

    It Just don't figure

    Points or electronic ignition? Sent from my iPhone using Tapatalk
  2. johncusano

    Broken rotor on crab distributor

    Stick with the rabbit ear one with nice bail clip other crab stuff is cheap,cap flew off twice on me.
  3. johncusano

    electronic crab

    6 volt pos grand? No soild core wires. And a pertronix 0.6 ohm coil. Sent from my iPhone using Tapatalk
  4. johncusano

    Heads Ache

    Hope you sealed the studs. Sent from my iPhone using Tapatalk
  5. johncusano

    Part Numbers for points 1948 ford crab

    Thanks. Sent from my iPhone using Tapatalk
  6. johncusano

    Part Numbers for points 1948 ford crab

    Who has part #s for points and condenser. So I might be able to buy them local. ( napa or oreillys ). Sent from my iPad using Tapatalk
  7. johncusano

    Problem with carbs. 94's

    Unfortunately I plugged mine. Sent from my iPhone using Tapatalk
  8. johncusano

    Problem with carbs. 94's

    I asked one question here about a gasket for power valve. Not one answer from all the experts. Except send them to NY to have rebuilt. Haha. Sent from my iPhone using Tapatalk
  9. johncusano

    Problem with carbs. 94's

    Sent from my iPhone using Tapatalk
  10. johncusano

    Problem with carbs. 94's

    Thanks. I guess I’m getting a lot of S—t for going modern over here. Sent from my iPhone using Tapatalk
  11. johncusano

    Problem with carbs. 94's

    Just says igniter. No 1 2 or 3. Sent from my iPhone using Tapatalk
  12. johncusano

    Problem with carbs. 94's

    Idk Tubman. Ur dist is easier to get to replace crap. I’m not saying I’m putting the pertronics back in. Right. I’ll have it for stock maybe. Sent from my iPhone using Tapatalk
  13. johncusano

    Problem with carbs. 94's

    Don’t think it was ever my carbs. The brand new pertronics electronic ign. Was bad. But the points back in runs like a champ. Waiting for a replacement module. Sent from my iPhone using Tapatalk
  14. johncusano

    4 down 44 to go

    I would think it better to heat the block where the stud goes in,not the stud. Replaced all mine in the winter. Just saying.
  15. johncusano

    Problem with carbs. 94's

    Blocked off Power Valves, kept stock 51 jets, leaning towards not enough power getting to coil or bad ground somwhere. No more points,Pertronics electronic module and Flame Thrower coil.Need to do some more checks,any info would help.
  16. johncusano

    Problem with carbs. 94's

    15 in of vaccum divide by 2 = 7.5 and that’s what I got for power valve. Is this the correct gasket? Sent from my iPhone using Tapatalk
  17. johncusano

    Problem with carbs. 94's

    Anyone have a pic of the correct power valve gasket? And what valve comes with a rebuild kit for the 94. From Joe’s antique? Sent from my iPhone using Tapatalk
  18. johncusano

    Problem with carbs. 94's

    15 in. at idle,20 when brought up, the valves that came in the kit have no valve on them.
  19. johncusano

    Problem with carbs. 94's

    Put in mid cam dual carb offy intake,2 94 carbs in my 59a engine. The carbs have 59 on the side of them i believe they are AA1. trying to get each set up one at a time, after a little bit of idling the engine shuts off like the key was turned off,got good spark thou.brand new ngk plugs are black...
  20. johncusano

    Exhaust Pipe/Wish bone arm.

    After two response's and both say no good between frame and wishbone arm. I couldn,t bring it to a shop so I spent the week end doing my own custom work and weld it to go thru frame holes. Exhaust is in with Smitty Mufflers,Got a few more things to do before I try and start it. New cam,new...
Back
Top