Search results

I have been a not so active member of this forum since 2010 At that time I have a lot of questions for members of this form. About a car that I inherited several years ago a 1934 Ford. It was my father's car The members of this form were very helpful and give me advice on how to get it up and...

I have a question on the front crossmember Would post pics but I can't figure how to post with my I pad I need to repair or replace my front crossmember as its cracked around the bolt holes and in the center and shows a lot of fatigue I was thinking if I repaired it I could actually lower...

Any one have any luck modifying the stock trans cradle to work with a Modern trans I was thinking i Could remove and modify the orginal cradle and bolt it back in any points on this would be great Also if you can post pictures that would be helpful Not sure if it makes a differance but I'm...

Btt

Btt

Thank you for all the replies I agree it looks better un boxed I will not be boxing the frame

Ok 2 say no 2 say yes Tie breaker vote anyone?

Btt

I have some leftover parts from my 34 resto It's best to call I don't get on line very often 262-365-7831 All the parts are from a stock 34 4 door woth a flattie and 3 speed and everything was working when I pulled this stuff off Here is what I have left I will ship anything but prefer...

I have a question about boxing the frame I have a 48 flathead that I will be installing in my 34 The guy I got it from said it had some mods done I heard it run on a engine stand but didn't drive it My question is do you think I need to box the frame as the flattie should be putting out...

I have a question about boxing the frame I have a 48 flathead that I will be installing in my 34 The guy I got it from said it had some mods done I heard it run on a engine stand but didn't drive it My question is do you think I need to box the frame as the flattie should be putting out...

I was working on the 34 today and was lining up the flattie Any how I got the mounts from speedway as they said they were the same as the factory mounts Maybe it's me but the speedway mounts don't seem to line up with the bolts in the frame so great This is my first go round on an old ford...

I working on my project and will have several parts from the car I would like to help a few guys get their projects on the road The gauges complete speedo fuel and amp gauge asking $200 obo Everything below im asking for resonable offers Clutch pedal setup The transmission with shifter...

Thanks for the help with my last post How many bolts hold the torque tube to the trans I removed 4 Also how do you remove the shifter when pulling the engine Thanks

Hello all I'm a rookie when it comes to old fords I'm in the process of pulling my engine and trans My question is how is the trans mounted to the frame? My cradle is caked with dirt and oil and I can't seem to figure what I unbolt Also do I need to support the rear and torque tube so I...

Thanks for the help I'm located in Chicago IL yes I'm very new to old fords I only know about ch**ys. I did find a 6 volt battery i put it on the charger and if it takes one I will give her a shot. I will give you a bit of history. The car has been sitting since 1993 when my dad...

Sorry I dont have pic's its a 6v system now and the car is all orginal with mechanical brakes and its the orginal 34 flattie

After much debate I have decided to keep my flattie in the 34 But with that being said I need some help I have no idea how to start it I have the key and there is some type of off and on switch on the column. I was going to take a 12v battery and a 12v coil to the dizzy and see if i...

I have managed to get the door stuck/locked on the 34 it will open from the inside but not the outside any help

I want to convert to open drive, was wondering if I can reuse the stock radius rods and attach them with a cross member I will not have many horse power just wondering about the strength of them.