Search results

Howdy boys, I have a few TT parts for sale. Here's some pictures. "C" cab. $125 '26 closed cab with doors. $400 3 Express beds. $300 each Tailgate $100 Crate of parts. Make offer Stake bed frame with slats. $200 High/low gear boxes. $50 each

I have several AA and A parts for sale that can be seen at the 2026 National Model A Convention in Pendleton OR, May 31-June 6. Here's some pictures. Cab - $1000 A Wheels - $25 -$35 AA drums and hubs - make offer Blocks - $75 One is an AA block. Complete and running Canadian engine - $1500...

Howdy boys, I have these two headlight buckets left over from the '32 BB I put together over the last 3 years. The reflectors are restorable, and the buckets are in nice condition. $75 for everything plus shipping. I can take them to the Portland Swap Meet in April if you're going. Thanks.

Yeah, figured as much. Thought I might use the leather one on my Model A pickup. I'm using a small piece of plywood now. Works ok! Thanks!

Howdy boys, I have two "radiator blankets", at least I think that is what they might be called, and I need a little help identifying them. One seems to be of a heavy material, the other is leather. What do you think?

Howdy boys, I have these two headlight buckets and reflectors left over from the '32 BB truck I restored and finished last summer. The buckets are nice, but the reflectors need some help. Otherwise in good condition. Any questions, let me know. Thanks.

Great advice guys, thanks! I'll keep you posted!

RGC1, I am in Pendleton Oregon. Are you going to Puyallop in Feb? I have a couple complete engines, one is out of a '39 or '40 truck. Has a 4 speed attached. The other is earlier, also complete. I think it is a '36 or '37. Let me know if you might be interested. Thanks.

Howdy boys, when I test the resistance from post to post on my ignition switch I get 9-10 ohms on Bat to Gauges, and .5 on Bat to Coil. Am I close? Thanks!

Found one, thanks guys!

Howdy boys, anybody know where I might find a new distributor shaft for my '48 F1 V8? Thanks.

Wow, thanks guys! I didn't know much about them but I feel a bit more edgimacated on them now! From the looks of the posts, I can probably do without one for now. I have a nice blast cabinet that I use for most everything, including carbs. Thanks for all the advice!

Howdy boys, your thoughts on an Ultra Sonic Cleaner. Thanks!

Howdy boys, so what are your thoughts on an Ultra Sonic Cleaner? Thanks!

Howdy boys, I'm looking for a vendor who sells V8 dist. shafts. Mine is worn at the bottom and I'd like to replace it. Can't seem to find a vendor who sells them. Surely somebody does? Thanks!

Howdy boys, well, so far no leaks! Guess we'll see how it goes when I fire it the first time. Standby........

I hear ya. Figured it would be easier to do what I did with the pan in place, rather than pull it and have to start over with trying to seal it again. Didn't get to work on it today as much as I wanted, ( I think we should get those weeds away from the fence since it's so nice out today! Good...

If it leaks this time, I'll remove the pan and clean it out so I will have a clean surface on the inside. Hope I don't have to do that!

Howdy boys, thought I'd give you the results so far. Yesterday I made 7 nitrile/cork gaskets, 3/4" diameter X 1/16" thick, with a 1/4" hole, and placed them over the bolts attached to the ring inside the pan. I then made another gasket for the plate, same material but 1/8" thick, and put it...

I'm going to give it try. I'll let you guys know how it works. Thanks for all the help and suggestions!