Search results

Went with a different carb , had to create new kick down , Car is a 55 crown vic with 292 2 speed fordamatic. Used a special adaptor and replaced the tea-pot Holly carb with a carb from a ford 390. Works ok , Thank for your replies

Could someone please send me a picture of how the fordamatic kickdown should look, I have the correct rod that goes down to the transmission and up the back of motor by the firewall. I am not sure I have the right accelerator linkage. Please post on ford barn or send to me at haw96aii@yahoo.com

does anyone know where I could get the clips to hold my weather strip/belt molding on my 55 crown vic, They look like staples.

I found a near perfect hood ornament on esty for $100. Got it yesterday ups. will put it on tomorrow. Thanks for the views too bad nobody had one Herman

Wanted replated or remanufactured 1955 ford hood ornament phone 952 442 2573 or email haw96aii@yahoo.com thanks Herman

Both vertical chrome sides had the same strip inside the chrome channel one is in better shape than the other but they do have a 90 degree angle about a eighth of an inch that fits into the rubber window gasket

The two side pieces of chrome that go up the side has a long I shaped rusted piece of metal that slips into the rubber seal it is one long piece that is almost as long as the chrome strip . Mine is still in the chrome strip one is worse than the other but the bad one is almost disintergrated and...

Thanks will do Herman

Could anyone tell me where I could get the piece or clip that holds the outside chrome that goes up the side of the rear window? My drivers side is all rusted away.It goes the entire length of that piece Thanks Herman

Does anyone know where I can get all the different clips for my chrome. Concours has 1 or 2 different ones e-mail me at haw96aii@yahoo.com or phone 952 442 2573 Thanks Herman

Thanks guys I will try that tomorrow Herman

How do you get the lock cylinder into the trunk sleeve does that pin push in or do you have to pull it out? E-mail me at haw96aii@yahoo.com Thanks Herman

Do you have the chrome piece that goes across the bottom of the 55 trunk or does that go with the trunk together e-mail me at haw96aii@yahoo.com thanks Herman

I need a crankshaft pulley with 2 grooves and the castiron powersteering bracket that bolts on to the water pump for a 1955 ford 292 e-mail me at haw96aii@yahoo.com Thanks Herman

I need a crankshaft pulley with two grooves for a power steering add on. Also I need the bracket that holds the power steering pump to the water pump for a 1955 292. If any one has either one of these two parts contact me at haw96aii@yahoo.com Thanks Herman

Thanks guys for all the info. I made a copy of all your suggestions and we will see how it goes. Thanks again Herman

I have a 1955 crown vic that I'm getting restored. It didn't have power steering originally but we have a pump but no brackets. Also would this be a separate belt or the same as the water pump and alternator. ? Are all 292s the same or are 55's different from the 56's? I believe the rack that...

I need the springs and frame for the drivers side back of front seat it is for a crown vic so it has the diip on the top inbetween the two sides . my drivers side is very rusty. e-mail me at haw96aii@yahoo.com or call me after 5pm 952-442-*2573 thank you

Do you have the chrome from the door panals for the crown vic . I have the back also do you have the chrome strip on the bottom of the trunk lid? e-mail be back at haw96aii@yahoo.com or 952-442-2573 after 5pm thanks

Wanted 1955 ford trunk lid chrome for bottom edge. I am restoring a 55 crown vic . Mine is all pitted and raged looking e-mail me at haw96aii@yahoo.com or call me at 952-442-2573 after 5 pm thanks