Search results

Are the wrist pins the same diameter? What is that diameter? Thanks to all

I have a 1940 221 block bored .080 over. New pistons would cost way more than 239 standards. can I just bore the block to 3-3/16? will wrist pins fit the 29 A rod. Thanks

Looking for a 50 F2 V8 fan shroud. Also an air cleaner clamp

Looking to buy T98 ****** for my 50 F2. Dont need a PTO. I live in NE Ohio. Thanks

Looking for a T98 ****** for my 50 F2. I want to swap out my crash box T9. Anyone close to NE Ohio. Thanks

I am going to rebuild my 50 express bed on my truck.my problem is that a previous owner removed the wood and welded a plate floor in. In doing so they modified the tail gate end of the floor. There is no longer a raised section where the boards stop. Photos and dimensions of that area would be...

Thanks, That helps

Looking for the rubber edge seal for the Wood in the bed. Is it flat? How thk is it? Who sells it. I have the express bed. Thanks

I wonder if the oe ordered the truck with F3 rear end. As far as I know it has always had a 14" rear end. Back in the late 50's the only 17" tires you could easily get were recaps. That's when we reversed the rims of a 16" for the rears and went to 16" tire all around. It aslo has the larger...

I have had a 50 F2 pickup since 1963 (third owner) that has 17" widow maker rims. I want to replace the rim with a one piece rim and reuse the original center plate. This would allow me to keep the original cap and look. what 17 x 7 rim will let me do this. I have a 14" rear drum so 16" won"t...

The needle on my 40 deluxe speedometer is laying horizontal and not up on the 0 mark. Is there a needle stop? if so where is it so I can get the needle in correct spot. I haven't removed the needle from where it was originally. It works fine except for the needle. Thanks

WTB any parts for the spare tire carrier for 50 F2. Thanks

I have a 50 F2 Truck. I saw a pair of front fender splash shields on Ebay which made me check my truck. I have owned it from 1963 and I don't have any on mine. Did they have them originally? they fit in the front fender behind the wheel. Thanks

Is there someone making bed parts for an express bed for a 50 F2. This bed is 54" wide and 96.05", rounded stake pockets and embossed bed sides. Also need a spare carrier.

My 40 coupe is missing the frame section for the rear motor mount, will a section from a different year fit? I think I know where there is a 48 sedan frame that has the frame piece i can get. i attached a picture of the frame section I am looking for. thanks

I took the switch apart and sanded the bakelite on a piece of sandpaper laying on a piece of glass. This way i knew it would be flat. I did the same with the three prong part. After putting it back together is was fine. Thanks to all

When I flip the lever to start on my Ignition switch on my 40 the switch enclosure gets hot. Almost to hot to touch. Is this normal? I took it apart and it looked OK. Is there a fix? Is there a short? Thanks

The book I referred to was "the 1940 Ford book". Sound like the front seat is correct but the rear is not. Should the rear have a carpet kick on the lower front on the rear seat? Thanks

I bought hinges from Mac's are they were terrible. They were tight and when I tried to free them up two of the arms came off. They were formed wrong and when I checked the hole sizes I discovered the both end of the arms are punched 3/8" but they used 5/16" rivets. My originals had 3/8" for the...

I need some advice on the seat covers for my 40 deluxe. The front seat only has two sets of ribs sewn in but the Ford book says there should be three. I assume the third set is in the bottom seat only because of the sedan back is split. My back seat has no ribs at all. I don't know if these are...