Search results

Wanted t87 heavy duty truck transmission - condition is not important as all I need is case and tower. Mine is cracked. The closer to Washington the better. Carl

Wanted t87 heavy duty truck transmission - condition is not important as all I need is case and tower. Mine is cracked. The closer to Washington the better. Carl

The Question is: Does the stock oil filter canister on an 8ba have a restrictor on both the inlet and the return line or just on the inlet. Thanks in advance for the knowledge of the Ford Barn members

Yes the cam must have been re-used as I see no refence to it being replaced, could be the issue indeed. How about fuel pump pushrod bushing?

Thanks form the thought. Should have said: I have checked that possibility by disconnecting filter and oil pressure issue was unchanged

Yes I do. The flywheel and pressure plate have been resurfaced and the disc is new. I figure shipping is about $40 to $45 Bucks. With that in mind. Tell me what sounds reasonable via Private Email. You will not be dissapointed in this set up. Regards, Carl

I have a stock 8ba in my 1950 f-1. I am considering installing a french flathead oil pump to boost oil pressure. I have had the pump for some time but have been reluctant to install it. Currently, oil pressure (running 10-40 oil) starts about 30+35 lbs at idle but drops to about 5 lb at...

Looking for the following 8ba/rt parts: 1. Oil Filter Canister with oil lines if you have them. Canister uses seperate head mounting holes, not head bolts and has intake near top, not center of can. 2. Coil Mounting Bracket 3. Distributor Vacuum Advance line from carb to dist. Please PM...

Still looking for T87D case and shifter to contain my gears . . . Thanks, Carl

I am lookng for a t87 HD Truck Transmission. Condition is unimportant (just need case and and thift tower) I have an extra complete T87 Transmission , less case and shifter and I just can't stand having the box of parts sitting around. I either have to build the transmission or sell the...

Thank you all for the wonderful education on 9.5, 10 and 11 inch clutch setups. I now realize I have a beautifully resurfaced flywheel with new pilot bearing, a researfaced/rebuilt pressure plate and new clutch disc all 9.5 "- for a car . . . Problem is I happen to have a truck . . . :-)

Barry, Thanks so much for the information it is much appreciated. Carl

Somewhere I read the method used for adding the proper amount of oil to the 8ba, truck optional 6 bladed fan,but can no longer find it. Method being something like; adding oil to a certain level and with set screw hole turned to a certain location let oil run out- yada yada. My truck red book...

I need clarification regarding flywheel/pressure plate set ups on 8ba/8rt engines. I thought 8ba/rt flywheels flywheels were drilled for 9", 10", or 11" clutches; 9" in cars, 10 and 11 in trucks depending on transmission. I have a flywheel and pressure plate set up that I thought was a 9...

I have a 1949 Mercury Radio that will also fit 1948-1950 F series trucks. I really want to trade this radio to someone who can use it in their vehicle and trade the following list of 1950 8RT engine parts: Flywheel (10 inch clutch), Flywheel Housing, Starter Plate, Dust Seal, Oil Filter...

If I change ring gears can I use a 6 cylinder flywheel on an 8ba. Regards Carl

Thanks for the explanation. Bushing installed. Regards, Carl

Shouldn't there be a hole drilled in the rear generator bushing to allow oil to flow between the shaft and the bushing. The one I removed has no oil hole and neither does the new one. Anyone have any experience or instructions to offer. Thanks, Carl

I have an 8ba machined block and new or lightly used rotating assemblies - pistons, rods, cam, crank + more as needed. 2-b assembled. I sent you a private email a few days back - no answer. If interested email back, post tele number or call me with number I sent you.

Thanks for the reply, I have another complete T87 transmission (less cracked case) if you know of someone in the market for some great gears. Regards, carl