Search results

  1. I

    1940 frame section

    looking for 1940 frame section for a repair. Driver's side from under the middle of front seat back to rear axle bumper .
  2. I

    strange noise in my flathead V-8

    My '40 started doing that. After disassembly I found the bearing thrust surface on the crankshaft was worn and the crank was moving back and forth. Haven't reassembled yet, but it seems to have been the only possible culprit. I know the 8BA is a different motor, but worth checking.
  3. I

    seafoam in flatheads ?

    I'm sure it can't hurt. And use this website to find Ethanol free gas in your area: http://pure-gas.org
  4. I

    Anyone tried this welding technique?

    Amps is Amps.
  5. I

    rod bearings

    Thumbs up, Mate! Thanks for your reply as well!!
  6. I

    1935-1936 Columbia dash controls installation

    38 Coupe is right about Columbia Two Speed Parts http://www.columbiatwospeedparts.com/Pages/columbiatwospeedparts.aspx John Connelly owns the business and manufactures and sells many of the parts you will need to complete the job. I've known him to take time on the phone to help you out with...
  7. I

    Flathead bearing numbers...

    Can anyone here help with this info? I'm trying to match (cross-reference) some rod bearings for my engine. The reference numbers I've found state that the bearings are to replace Ford bearing part # 81A-6211-A5. In the Ford book I have, I only see # 81A-6211-A, -C, -F, -M, -Q, -V, and -KK (not...
  8. I

    rod bearings

    I have a Federal Mogul bearing cross-reference book and the 9725 SB 10 crosses to a "Packard 6" with the following Packard part numbers referenced: 335827, 358231, 341701, 362500 and 387600. The 10 after the SB likely means they are .010 u/s. I hope this helps.
  9. I

    Starter voltage choice...?

    Here's an interesting way on FlatheadV8.org to convert your 6 volt to a 12v for more efficient operation (according to the author) http://www.flatheadv8.org/12vStarter.htm
  10. I

    No fire at the plugs

    Thanks, John! Royal, let us know what you have to do to solve the problem/s. Often it's a list of things. I'll be curious to know.
  11. I

    Overheating Flathead

    My '40 was overheating (on the gauge) and getting the point gap right and advancing the timing made a significant difference!
  12. I

    Hi from NC

    Welcome! I'm relatively new here too, right in the middle of South Charlotte! Happy to share tips, tools and parts!
  13. I

    No fire at the plugs

    The more research I do, the more I realize how challenging the ignition is on these early V-8s. Knowing little, I'm responding assuming you have the "diving helmet" distributor versus the "crab" style or later, more modern distributor. If not, some of these things are still worth a look...
  14. I

    1940 Sedan Circuit Breaker

    If your wiring isn't well dressed, the harness can get in the way of the clutch and/or brake pedal, causing your lights to flicker.
  15. I

    1940 headlight door screws etc

    Roy is THE MAN when it comes to correct nuts, bolts and screws. Very friendly and reasonable. He sold me the correct headlight door screws recently. Here's his link: http://www.fordscript.com/ford_bolts/index.html
  16. I

    1940 ford running boards

    When do you think you can post pics of the running boards? Any evidence of prior damage, especially on the passenger side? Thanks.
  17. I

    Echlin IC 55 Coil

    Some excellent information here. Thank you. I'm currently running a N.N.S. (new new stock :) aftermarket 6v on the wheel well (for temperature problems) on my '40 V8. I thought this one might look cool there but wanted to make sure it would work. Thanks again.
  18. I

    Echlin IC 55 Coil

    very helpful rod. thanks
  19. I

    Echlin IC 55 Coil

    Can anyone give me any information on an aftermarket Echlin IC 55 Bakelite coil? The exterior is in excellent condition and the bulb seems intact. It may be N.O.S. Thanks.
  20. I

    Response on 15% Ethanol

    Support this sight and keep track of Ethanol Free Gas! http://pure-gas.org/
Back
Top