Search results

Thanks Brent. That is what I needed.

I will be having my parking brake handle re-plated by a shop near me in Omaha and have a couple of questions. Where does the dividing line between the upper chrome finish and the lower butler finish lay? Does the grain of the butler finish go around the lever, not lengthwise?

I am looking for an original horn that would be correct for a friends 31 pickup truck. Please let me know if you have one your would be willing to sell. Thanks, Dave

The inspection cover plate can be a challenge to install even with the engine flipped upside down. The plate often contacts the pan gasket making it difficult to line up the holes for the bolts plus its pretty tight quarters between the pan and the flywheel housing. One thing you can do is to...

Nathan -if you have a 50/50 mixture of coolant and distilled water you do not need to do anything except to use a squeeze bulb type tester to make sure the freeze protection is at -34 degrees. If you are not using the 50/50 mix I would suggest flushing it out with water and then putting in a...

One has been found.

One has been found.... Thanks, Dave

I have a Model B engine that has been refreshed and just needs to be assembled to be a good running engine. A fellow club member is interested in the engine and I was hoping that someone would be able to reach out to give me some guidance as to where I should be with pricing it.

I have an AA truck that has a date stamp of 1-29-29 on the gas tank. I think it is probably one of the very last to have the left hand parking brake lever. It is also one of the few trucks remaining that has not had the recall of the front axle completed. I had an experience with the truck...

Zip tie or clamp the light switch lever to one of the steering wheel spokes to keep it in place while you are installing the spring.

Thank you.

I have a gentleman that has an early car with the solid front cross member that is most likely going to need to have his timing gear replaced. To clear the cross member it looks like the engine will need to be tilted up a fair bit more than needed on cars with the later style cross member. Will...

Werner, Your running Avgas 102 concerns me. Am I correct in that the octane level of that fuel is indeed 102? High octane fuel is in my understanding is formulated to be more difficult to ignite than the lower octane fuels preventing the fuel from igniting before the spark actually takes place...

If you would have two distributors and assuming the one you have in it now is timed correctly you can remove it and set it aside. Install the second distributor, time it to the engine and drive it for a thousand miles. After that you can remove it and reinstall the first one and it will still...

Place a dial type meat thermometer directly into the water and hold a piece of cardboard in front of the radiator. Set the hand throttle to a quick idle and watch the thermometer like a hawk. Bring the temperature up to 190 and adjust the cardboard to hold the temperature there for a few minutes...

This has worked well for me to get the beads in. Mount the wheel on the car. Using a jack lower the tire down to the ground allowing the tire to squish down forcing air out of the valve stem. Once the air has quit flowing out attach the tube and feed beads in until they stop flowing. Then jack...

Where are you located? Perhaps someone could come over for a second set of eyes on it.

I am somewhat suspect of your temperature gauge. Test the temperature of the coolant by placing a dial type meat thermometer directly into the coolant by removing the radiator cap. Picking up one of the exhaust gas detection kits from your local auto parts store would be a good thing to do...

Spray it down with straight Simple Green, lay it flat in a large plastic trash bag and seal the bag up with as little air as you can. Allow it to "soak" for a day or so and reapply more Simple Green. Repeat until things are softened up and then spray it off with a garden hose. To clean grease...

Round the edges of the hole a bit. Cut a circular or square piece of cotton tee shirt material and saturate it with some RTV sealant and after cleaning the area with solvent apply the patch over the hole. Won't be a structural repair but neither will J.B. Weld. Keep an eye on it and drive it.