Search results

FSIgnition has what you need FS Ignitions 220 N 1st St Ponca City, Oklahoma 74601-4258 (580) 762-8322 fsignitions@outlook.com

While retiming my engine I set it improperly and when I went to start the engine it kicked back and misfired. After setting the timing properly, I went to start it and the starter sounded terrible, although it turned the engine over. I removed the starter and found that the Bendix spring had...

I am using Spectra but it looks just like the Holly. I am running a log intake

I have a gauge attached to the outlet side of the regulator to set pump pressure. ChatGPT suggests hat possible problems could be a plugged filter, restricted fuel line, or blocked tank vent. - Weak pump output or low voltage at the pump. - A restriction or malfunction in the regulator. The...

Re: Modified A will not Calihute I found this posted by WUGA . He said he installed a Brierly head on his banger using the FSI distributor. It was getting way too much advance. When he talked to Jim, he told him that FSI makes two distributors, one with 28 degrees of advance and one with 18...

I tried a leakdown test on my model A and when you would get a cylinder at top dead center and apply the air test it would the car and come off dead centyer and of course leak air. Could not stop the engine from turning when testing.

Modified A Charlie put adjustable main jets in the carbs when he rebuilt them. I am going to open them up and see if that helps. If I could determine whether it is getting to much fuel or not enough it would make it a lot easier. I raised the fuel pressure and the carbs started getting fuel on...

I built a 31 coupe and raced it at TROG last year and it ran fine. This year I painted the car and converted it over to 12 volt. As part of painting, I repainted the motor. To do that I removed the exhaust and intake manifold. Every since I put it back together it does not run right. The engine...

I want to lower the rear of my 31 coupe and am looking at rear spring. Speedway has a 3 springs with reversed eyes ranging from 198 dollars to 537 dollars. One is 48 1/2” perch to perch, one 46 1/2” and the cheapest 46”. I am wondering if any Barners have used these springs on their A and will...

I recently purchased a ’32‑style dash panel for my Model A and plan to install it along with a full set of electric gauges. I’m using Speedhut gauges: GPS speedometer, oil pressure, water temp, fuel level, air/fuel ratio, plus a cell‑phone charging port. I’m keeping the original cowl fuel tank...

Has anyone heard of or can tell me where to find a 6 volt air/fuel sensor kit? Would need a 6 volt 02 sensor and guage. If not is there a way to monitor air/fuel ratio without this setup?

Pacific in Australia makes a quick change for a Model A. Halibrand made a Halibrand 101 for a Model A. Was there anyone else that made a quick change for a Model A? If so what model or series or serial numbers are they.

I am building a street and strip A Coupe and would like to put a Quick Change rear end under it. I know Halibrand made a 101 for A models and Pacific in Australia currently makes one. Are there others that can be adapted. I want to use my spring over the differential, closed drive line and the...

Anyone out there have a hilibrand 101 quick change they would sell on know who makes a new one? Winters does not.

Does anyone have a PDF that I can give to my machine shop for them to properly locate the V8 clutch holes to drill them on the lightened flywheel? Lighten flywheel drawings would also be good to have.

I am building A 31 coupe for Street and Strip. I have acquired most of the parts for the engine build which consist of .80 oversized pistons, 1.70 intake valves, a Brierley cam, 6.5 head, dual strongberg 81’s, reds headers and a FSI centrifugal distributor. I plan on using a 39 synchromesh 3...

10 U C - This is to be a Jalopy I am building to drag race at TROG. It will have 1.7 in Intakes and stock size exhaust with new style guides and adjustable tappets. I will be running twin 81's with a Jim Briley cam. Engine is overbored 80. Rods and mains are newly poured babbit with a Burtz 6.5...

JohnNeilson, What Overhead Valve conversion would you recommend?

I would get another block but this engine has just been completly rebuilt with new Babbitt in the mains.

In the process of porting and polishing my intake and exhaust ports, the number one intake port developed a hole in the port. See picture. Is there a way to repair this hole? All of the others are ported with no problems. The hole opens into the water jacket in the block. There is no pressure...