Search results

Front Hood emblem and latch mechanism and hood hinges. Fit 1942 - 1947 Excellent operating condition. Front and sides of hood also available. Top of hood was removed. Hood emblem and latch mechanism $125.00 Hood hinges - $50.00...

I'm looking for a good source for Ford Flathead carburetor spacers. My 8BA sits with a slight tilt and I would like to get my carbs sitting correctly without the slight lean. I'm running 3 Holly 94's on an Edelbrock intake. Thanks.

What year Ford pickup hood are interchangable on a 1947 cab?

Sold - For sale is a 1941 Ford car steering column and three on the tree column shift shaft mechanism. There is no inner steering shaft, or box. The key and column lock mechanism is froze up. Parts have been sand blasted. Cash only. Shipping can be arranged at buyers expense.

For sale is an open drive driveshaft from a 1950 Ford 4 door car. It was mated to a Flathead V8 with a three speed side shift transmission. It includes the front yoke and the rear universal joint. From what I have read, it sounds like Ford used the same driveshaft in all models of their shoebox...

Who makes the best authentic sounding 12 volt Ahooga horn? Many on the market and most with reviews indicate terrible sound.

‘49-‘51 V8 8BA bell housing / starter plate SOLD. Steel stamped bell housing with starter plate and linkage parts for 1949 - 1951 Ford Flathead 8BA engine. Shipping charges not included and are the responsibility of the buyer. UPS charges can be estimated based on delivery location. Cash...

Ford Open Drive Trans Mount: This was used with Ford 3 speed transmission to allow for an open drive driveshaft (no torque tube) on 1942 - 1952 Fords. Set up allows for conversion to open drive on older model Fords that used a torque tube. Includes open drive rear retainer/trans mount with...

Not sure what this came off of. Appears to be a bug catcher that was mounted over the cars radiator grille. Seems to have a shape similar to a 1934 - 1937 Ford but not sure. Used condition with surface rust. See photos. Shipping not included and responsibility of the buyer. Local pick up or...

1948 - 1952 Ford truck oil pan. Highly sought after flathead pan due to the rear sump and clean out on bottom of pan. Pan is in good original condition, with no dents and nice straight rails. Just needs cleaning, sanding and paint. Works well when putting a Ford car 8BA or 8RT truck (1949 -...

1949 - 1953 Ford Flathead V8 oil pan. Standard center sump. Includes sump pick up, drain plug and dip stick (no tube). This pan has been cleaned and painted. It came off a fresh rebuild that went into an older Ford frame (needing a rear sump). Great shape. Still has fresh never used rope...

Sold - For sale this 78-7006 Ford Flathead 3 speed top loader transmission. For use as parts; it includes a two 5/8” decent 81A-7222 later style shifter tower and a rusty gear set that is stuck (Does not turn). With some effort, some gears/shafts may be rescued for future use but it is...

1937 Ford bumper - sold SOLD. - For sale is this 1937 Ford bumper that came off my 1937 Ford coupe. I do not recall if this was the front or rear bumper as one of the two bumpers removed was used in another project. The dimensions are as follows; total length is 61 inches. Height is 3 1/2...

I have mounted my external oil filter on the firewall and will need to buy flexible oil lines with the correct connection ends. I know that Ford used different types of threads etc. and so I’m asking for some advice. Don’t want to get the wrong parts. I do have the restrictor fitting already...

I put a 1949 8BA flathead with an Edlebrock intake and three Holley 94’s in a 1947 Ford pickup and attempted to use a typical ford accelerator pedal and push rod to operate the center carb. I have a good progressive linkage from a reputable source on this and the carbs all open up correctly but...

I am looking for a source for the vacuum port plug that fits the Holley 94 carb. It appears to be an odd size / thread type. Any one have any info that might help me locate them?

Does anyone have a current source to buy a coil offset bracket that moves the location of the coil a couple inches further away from the distributor? I know Luke’s custom machine and design out in Vancouver BC used to make them but they don’t return any calls so I’m assuming there no longer...

Anyone aware if Luke Balogh (Luke’s) business is still going and if he still makes his coil bracket - part # 12043 ???

Completing install of rebuilt 1949 flathead 8BA motor. Not sure which end of the fuel pump push rod goes down thru the bushing. Rod has three parts to it. Center is a hollow steel tube 7 7/16 inches long, with on end having a 1/2 inch end attached and the other end having a 2 1/8 inch shiny...

I have an old ford that has been converted to 12 volt and would like to use some very old headlights that were/are 6 volt. I can get the original bulbs and wondered if someone makes a 12 to 6 volt reducer that I could install for this purpose? I also wondered if anyone is aware of a company...