Search results

I am looking for the turn signal parts identified by arrows, for a 1953 Mercury. They are the same for 53' Ford too. Thank you, Roy royd13483@aol.com (303) 838-2028 (land line)

I am used to seeing, only one temperature port on the drivers side, yet these have two. What was the application and the years they were used. What was the extra port for?

So true.

This question is about my 53' Mercury with a stock flathead engine, and the original stock distributor, along with the original stock Holley 1901 Teapot carb. Plugs 1,4,5,8, are burning normally and clean, but plugs 2,3,6,7 are burning rich and black. To restate: the 4 corner plugs are burning...

My wife and I took our cars (hers - 1970 Cougar XR-7 and mine - 53' Merc convertible) to a local car show today. Three nice A's showed up, that I hadn't seen before. Mine was the only Flathead V8 at the show. It is getting harder, every year, to find Flatheads in the cars any more.

Wanted: Carburetor linkage for 53' Mercury "Teapot" with Merc-O-Matic transmission. (standard transmission cars didn't have it) Thank you, Roy royd13483@aol.com (303) 838-2028

What is the purpose of the two holes, in the 53' Mercury Teapot linkage?

While searching for a good description, as to how to adjust the accelerate linkage, on a 1953 Mercury to factory specks? I did find a good description of the proper set up in my 53' Merc-O-Matic, auto trans manual. It mentions a Tool # 77230MAA - 1952-1953 Models. If you have one laying around...

Wanted: Complete throttle body for a 52'-53' Mercury 1901 Holley 'Teapot" LIST # 882 Wanted: Complete throttle body for a 52'-53' Mercury 1901 Holley 'Teapot" LIST # 882 carburetor, for a automatic transmission (Merc-O-Matic). Roy Lange royd13483@aol.com or private message me.

How do I decode a Holley 1901-FF carburetor? Second question: Did they make different sizes of the "Tube Assy (carb main well)" # 13 on the Daytona parts sheet, for the rebuild kit. When I put the wire provided in the kit, down the Tube Assembly on two identical carbs, it goes down one and...

Wanted: Airtex E8902 6 volt fuel pump. Roy Lange Conifer, Co royd13483@aol.com (303) 838-2028

Anyone have a source for a rebuild kit for a dual action fuel pump for a 1953 Mercury? I have tried about everyone that I have used in the past and no luck. Thanks in advance.

A friend of mine is currently building a 8ba engine for his 53' Merc. The issue is that he is using Edelebrock heads with fins and wants to install the completely assembled engine, back into the car, with out disassembling any of it. Has anyone here done that and where did you fasten the lift...

Looking for the factory, drivers side exhaust manifold, for duel exhaust, for a 1953 Mercury/Ford. The part number is FoMoCo: # EAB 8431 A. Thank you, Roy royd132483@aol.com (303) 838-2028

I posted earlier requesting a picture of a 1CM "crankshaft" when I meant to say "camshaft". Let me try this again, does anyone have picture of a 1CM camshaft? Thank you.

Does anyone have pictures of a 1CM crankshaft? Thank you.

Stainless steel or chrome plated pot metal – vent wind frames for 52’-54’ Mercury’s a Stainless steel or chrome plated pot metal – vent window frames for 52’-54’ Mercury’s and Fords Back, 70 years ago, Ford and Mercury’s came with stainless steel clad vent window frames, for a very short...

70 years ago, when these cars were built, the screw jacks (used for the convertible top and the power seats) came with a clear cover, over the threads and housings. Over the years the clear plastic covers have turned yellow and become brittle with age, rendering them unserviceable. See pictures...

I am looking for a set of door edge guards for an 1953 Mercury Convertible (model - 76B). The part number is: BG 19292-B E-mail: royd13483aol.com Phone: (303) 838-2028

My "cigar lighter" did not work, so I decided to take the time to look into it. I did a continuity test and it was an open circuit, when the lighter was pushed in. I took off the "cigar lighter fuse" and found that to be the issue. Since I had another one that tested good, I decided to take the...