Search results

Here is a Model B distributor complete with cap and wires. Missing the rotor, don't know where it went. I bought this several years ago from a fella off the HAMB. He said it was rebuilt. I ran it probably 100 miles and decided to go back to the Model A setup. Now my A is gone, so I need this...

SOLD Admin please delete

I will need to drop the oil pan on my 30 Tudor soon, the oil plug bung is spinning with the plug :( Anyway while the pan is off is there a way to check a pump other than install it and check it with a gauge? I am asking because I have an extra motor that I will be borrowing the pan from and...

1934 Ford 3 window replica SOLD PLEASE DELETE!!! Sold

Complete brakes minus the backing plate mounting bolts. Plus 2 new rear grease seals. I went hydraulic. $50 plus shipping.

no longer valid

Hey all, I have a 30 Tudor that needs new body mount blocks eventually. I am missing the back ones. Until I by a new set I was thinking of cutting my own to temporarily use. What is the thickness of the blocks?

Hey, I am looking for these pieces to mount my bumperettes. you can call me at 541-260-2368 or ebcaaron@gmail.com thanks!

So I am driving my 30A, when I first got it running I clearanced the bearings, ground and adjusted the valves, new head gasket. It ran good but with a bad vibration as the rpms would drop. Meaning you could rev it up in the driveway out of gear, and it would vibrate after letting of the gas. I...

I know this is a long shot on this traditional restoration site but I need a clearance lens for a BLC904a headlight.

I know this is a long shot on this traditional restoration site but I need a clearance lens for a BLC904a headlight.

Hey, I am going to reveal another layer of my ignorance. What does it mean to have the radiator rodded and what does that normally cost?

I just completed tightening the clearances on my mains and rods. I used the foil interference method. As I got to the last rod the engine was getting a little stiff but once I got it spinning it seemed fine. I got it all together and started it up. I ran great, less vibration. It was getting a...

Hey all, many of you have read my postings and have put up with my ignorance. Better yet alot of you have been helping me "get my mind right" about the "Mighty Model A". Many of you don't know that the engine that I have been working on was in fact an engine I bought of eBay for $175 that was...

Hey all, I am collecting parts for my hydraulic brake conversion of my Model A. I am looking for F1 pickup truck front hubs, drums and bearings. Also 40 Ford rear hubs, drums and bearings. Thanks Aaron 541-260-2368

I need to change the head gasket on my 30 Tudor and was wondering if I can re-use the studs. Also (not to start and argument :D ) what gasket should I use? It has a copper one now. It is a stock compression head. Copper? other? Thanks

after getting something too tight and breaking it I am asking the brains. I am replacing the rubber in the stock A rear motormounts and also the front with an original style 3 spring and plate setup. How tight? Just so I can put the cotter pin in? I don't want to squeeze out the rubber on the...

This is take two at manifold gaskets. The first ones where cheepo paper based from a complete engine gasket set. They got oil soaked from my Marvel Mystery Oil cylinder treatment prior to start-up and squeezed/blown out after start-up and re-torquing. I bought some high quality copper clad...

Well after owning the car for 2 years and owning this current (used off eBay) engine for over a year; it is in the car and running. Click here for the video Sorry for the long video. The smoke is from the Marvels oil I put in the cylinders about 6 months ago. I had driven the bottom lead...

This is probably a dumb question, but who makes the snyder head is it made by snyder's themselves? And where is it made?