Search results

Hi, i´m desperatly looking for a door latch for a 1946 Delivery, the rear door, any one, please? /Tom

Hi guys, i´m looking for a complete rear door latch for a 1946 Ford Delivery. /Tom

I'm going to do some hot riveting today and have all necessary items but can't remember how much the rivet shall stand out, to build a perfect head. I believe it's 1,5 x diameter but i'm not sure. Please guide me. /Tom

Which connecting rod suites a 30-31 column best, as a column drop? What do You use?

Will the upper cover at the spark and gas rods, go down, when i loosen the screw, or up, when i pull the steering wheel, with the steering wheel puller that i don't have... yet. I have tried to tapp carefully with a bronz hammer on shaft/nut but nothing. Warming perhaps? Are there any easy ways...

Hi all, i'm looking for a LH drivers side 1926-27 spindle. Good threads, good bearing surface and not pitted. Hope I have not scared away all now. /Tom

I hope that You maybe have some good advice for me. I have lowered my -23 roadster 6" rear and 8" front and i'm very satisfied with the stance. What do You prefere, heat and bend the steering arms to clear Z bracket i made or use model A arms instead. Or make a bend on the tie rod. How did they...

I wonder if the model A's left and right steering arms will fit in the model T ones? Are the holes the same diameter?

I was going to change wheels from wooden to wire wheels today. To 21" Model A ones with adaptors. When i disassemble the wooden wheel i find that the gap between spokes and hub is filled with...lead..?? or metal filler. All hubs are stuck.. An easy job now turned into a problem. Is that the way...

I changed the Motorcraft, modern style top spark plugs to Autolite 66 14mm with an adaptor and the center and ground electrod sits further into the combustion chamber. I did this after i put a modern style distributor in my car. Should i be concerned about this? I also have a Z head.. No, my car...

When my roadster arrived last summer it did not turn over but with a lot help from You, it's now running. I like both Model A's and T's so i use studs instead of bolts and a outer case from a Packard coil where i put the 6v in to. The humming photographer is a friend, driving the red Cadillac...

I ordered the engine pan & hood shelf block set 1923-1925, because they were missing on my car. Now I have absolutely no idea how they should be mounted. Maybe someone has a picture how it should look like. /Tom

What kind of bewitching tricks shall i use to install the hood hooks. How do i fix it with just two hands..:( Are there any simple and easy ways? The springs are really hard to compress. Please educate me. /Tom

I saw somewhere that if i use a distributor i can use a jump wire from mag to bat post on ignition panel, so i can have the ignition switch in either mag or bat, correct? Can i use a T-5038, amp to switch wire, or does it have to be a thicker one? /Tom

I have replaced the old fuel line and ordered new fuel line clamps but do not now how they are going to be attached. Please aducate me :) What function does the angeled tab have?

Several vendors sell the T3081-HVOL high volume outside oil line. It has a brass elbow 3/8 NPT - 3/8 CT (?) with flare nuts. I would like to change the copper tube to a rubber hose. Maybe some of You know where to find such a hose fitting. A female adaptor barb and fips. I have problem to state...

I would like to know how much gap there is between the hogs head and the block when everything is bolted together, without the felt gasket. Can i use a bead/string with "the right stuff" instead of the original felt? Will it fill up the gap? All the bolt holes in pan and cover line up perfectly...

Hi everybody, i'm looking for a Model B 1932-34 exhaust manifold in good shape. /Tom

Hi, i'm looking for a HM-7R lamp bracket bending iron. /Tom

I wonder i You could give me a hint which vendor is selling the WOODEN 5 to 7 pieces upper tack rail list, like the one thats missing :rolleyes: on Multi's Roadster. (not the modern hard rubber version) Is Snyders TWD-1243-2 what i'm looking for? /Tom