Search results

Is there anyone out there that has a fresh built 36-48 stroker that they need to sell... I have cam, heads, etc... I just need a fresh built 'short' block Los Angeles, Vegas, Reno areas? Message me here or call Craig 760-258-6540 No bogus Moneygram, cashiers, phonepay crap... I will pay cash...

Hello all... Has anyone used Flathead Jacks oil pan for a 39-48? They are a little pricey, so Id like to hear pros and cons from you guys that have used them. Anyone have a picture of a motor with one on it? Thanks all! Craig

I had a few people asking for updates on my turbo project. Its going, but slow... My damn job got in the way..haha Anyways.. The headers are almost done, then I have to build the carb boxes, intake supply's, linkage, and exhaust dumps. They dont know it yet, but im gonna have H&H build a new...

Hello all... Im looking for a drop column ignition set for my 1936 ford truck... I dont want a nice restored unit. Im looking for a used complete unit. My truck is a daily driver and doesnt need anything nice... Thanks!!

I have a 1930/31 body that im looking for a frame for. The guy tells me that its a T frame that was converted into a hay hauler in the 40's. He will give it to me if I want it. Its in the weeds and sorry for poor pictures. My body is a rough chopped two door.. It will have a flatty and three...

Hello all... Im putting an oddball motor together and im wondering how many different custom/private production oil pans were avail for the 37-48 engines? Does anyone have any names/manufacturers that I can look out for? Id like to find a nice pan for my project. Im building a twin turbo...

Hello... I cannot reply to anything in the Swap Meet. Im having to PM the sellers. Any ideas?

Hello all... Im getting ready to mock up a twin turbo setup on one of my spare motors.. Its going to be on one of my 41' V8 motors. My question is, where do you buy header tubing, 45. 90, and U bends? Im looking for 1in or 1 1/4in. Any thoughts? Ive already made my flanges.. Just need pipe...

Hello all... Im getting ready to mock up a twin turbo setup on one of my spare motors.. Its going to be on one of my 41' motors. My question is, where do you buy header tubing, 45. 90, and U bends? Im looking for 1in or 1 1/4in. Any thoughts? Ive already made my flanges.. Just need pipe. Im...

Hello again all... Im going to put a motor together for my 36 Ford Truck that you see on my avatar... Its too rough for stock, and I like noise. Im going to keep it all stock, but id like to build a nice sounding/looking motor. Im sure id have better luck on the HAMB, but I dont like the...

Hello all.. I have a friend that just got to Reno, Nv for Hot August Nights with his 1937 Ford.. All original 85hp V8 6Volt. He went to get it off the trailer and the starter failed. Does anyone know where he can find one ASAP and also someone that can install it? I wont be up there until...

Hello all.. I have a friend that just got to Reno, Nv for Hot August Nights with his 1937 Ford.. All original 85hp V8 6Volt. He went to get it off the trailer and the starter failed. Does anyone know where he can find one ASAP and also someone that can install it? I wont be up there until...

Do not send money to these people or addresses: Karren Hardy Jason Hardy Glenn Hardy Anything moneygram They just tried to get me to send money for parts without pictures and I looked them up.. Sorry for the real Hardys in Kansas, but for these idiots Id like to send a bullet BAD PEOPLE: Jason...

Hello all... Ive been searching for a set of Fenton heads for awhile... I just bought 'one' off of ebay, and I need one more.. Anyone have one head laying around that you want to sell?? PM, Call or Email Thanks, Craig 760-258-6540 lecktrix@yahoo.com

Hello all... Im new to the flathead world, and im about to start a rebuild. I know the issue has been discussed tons of times on here... but what should I do... I have seen the exhaust port stands and the front and rear stands. I have two 1948 V8's that I need to tear down. I have done tons of...

Hello... Someone took out the original windshield and just stuck in flat glass with some rubber trim. Id like to get the original tilt out frame and under dash crank unit. Reply here, or shoot me an email.. lecktrix@yahoo.com Thanks!! Sorry... For a 1936 ford truck

Hello all.. Im putting together a sweet 1936 Ford Truck with a '48 motor in it. It has a nice Fenton intake, and id like to keep the look all the way through. Let me know if you have anything. You can email me lecktrix@yahoo.com I also need a 12v Starter, Head Studs, aftermarket distributor...

Hello all... Ive had my eye on this car for years, and the owner finally decided to clean his field out. There was a lot more, but this is the only one that perked my interest. About 6 years ago, a fire went through his field and destroyed all of the cars out there. This one is extremely rough...