Search results

Hi folks, im helping a friend with his rear brakes on his AA truck. It appears that the rear brake adjusters are stripped. I assume they are threaded so as you turn them in they would move the wedge in to expand the shoes out closer to the drum surface. they turn but dont seem to go in. Is this...

can any tell me if the top mounting holes for the spare tire bracket are threaded? My gas tank cover has no holes drilled but the bracket is there underneath. I cant tell looking from under car but I suspect they could be. 34 car. Ken

Hi everyone, I'm hoping someone could send picks of there trailer hitch set up. I want to build one to fit my 34 tudor. Just looking for ideas. thanks so much. Ken

could use some suggestions as to stop my gas cap from spilling when full. I have tried a new gasket on original cap, tried a new cap as well. Car has a new drake tank with a spring loaded flipper. (34 ford). Ken

any one know where I can get rear floor mats for a 34 tudor? Ken

Hi folks, my 34 horn has been a pain. I cant seem to get a reliable ground. I have cleaned the contact at the bottom where the wire harness and rod connect as well as removing the rod from steering wheel bending the tabs and cleaning that area as well. you can here a faint try and once in a wile...

hi folks, its not a t but maybe I could get some help. I have a 1923 fordson. I want to here the old girl run. I have a new headgasket. I have no clue from ware but it came with the sale. It has a copper side and i wonder copper up or down? thanks Ken

So, can someone tell me the correct orientation of the light switch when all lights are off. Vertical or horizontal ? Thankyou Ken

Hi everyone, does anyone know where I can find parts for a 23 fordson? I just purchased one in good shape for 101 yrs old. the engine is free and I think it would run but it has cracked intake and exhaust manifolds and other small parts missing. Thanks so much. Ken

how does my 34 horn make a ground at the wheel and can I take it apart to clean contact. it tries to work but I think its a poor ground at steering wheel. I can make it work grounding it at the horn itself. Ken

My 59ab doesn't start well when at temp. Engine starts cold instantly but once at driving temp (180) it will just crank and crank unless I feed it fuel with pedal. carb is rebuilt 97. engine is stock. fuel pump rebuilt and fuel flex line has a check valve. I thought about trying a carb riser...

anyone have charley ny phone number? Thanks Ken

Hi folks, I have a bind in my stock 34 steering, it seems to be most notable on a road with sharp curves and a high crown. I have some play but minimal. should I rebuild the steering box? Where might i find a good quality rebuild kit? My tie rod ends and king pins are all in good shape. thoughts...

Hi folks, got my new front floor mat and plan to install it soon. Can anyone tell me does the separate peace over the shifter go under or over? Also there is no cut out for the batterie so I assume you have to lift the mat for access? Thanks so much. Ken

Hi folks, so I have a Drake tank in my 34. The gas cap is original and I put a new cork (hand made) gasket on it, every time I fill up it leaks out, I'm careful to stop pumping too close to the top and the tank even has a flipper to trap the slosh. I tried an after market cap as well with no...

Hey folks, forgive me for asking this on the barn but its were I am comfortable. For reasons too long to explain I put an electric fan in my 34. The car is converted to 12v and I'm using a typical GM alternator. All works well except I notice when the fan starts and I am at idle the amp gauge...

I'm trying to locate a shark fin ford jack for my 34, I see some on ebay occasionally. Can someone tell me why some look like they are cast and others look more like stamped steel? Ken

Looking for a working 34 jack with handle. I believe it was the shark fin style. please pm me if you have one to sell. Thanks Ken

Take a virtual ride in my 34 Ken https://youtu.be/11QwDqr78lc

Does Anyone have info on headlight alinement? I'm thinking if I had some measurements I could use tape as a bulls eye on my shop door. Help?? Ken