Search results

hello i just put a new clutch disk and pressure plate in my 30 tudor. i adj the finger to 5/8 and went to adj the peddle . i have the peddle adj as far as it will go . when i Engauge the peddle it dose nor seem to disengage the clutch all the way the through out bearing seems to barely move...

hello i am replacing my clutch and need to replace throw out bearing my question is how do you remove the bearing from the hub and put the new one on i do not want to damage anything 30 tudor thanks you kevin

hello all i need sme help this is not a foed question but a 1935 ply question i am working on my father in laws 35 plym i have it back togeather an has beed running great the other day i drove it and when i turned it off it would not start a few days later it starts right up drive it rund grat...

timer assy question? Update fixed hello I have a 1923 t i have had a true fire system for over 30 years but i think it is going bad i am going to switch back to the coils and timer and roller assy my questions is witch way dose the roller go on the shaft which part of update I found that the...

hello my 23 has started to run bad i had the head gasket replaced and all the carbon cleaned, it idles fine but back fires ans loss of power. i do not have a compression gauge. i removed the no 1 plug and it was black with carbon. i have fire to all cycl. i have a rebuilt carb and good gas flow...

hello all i finished my brake job. The brakes work great. the car will now stop.My question is when I apply the brake they squeak. I have new cast drums and relined shoes with woven pads. Will this stop making noise after i ware them in? Thank You Kevin

hello i have my brakes installed and hooking up the brake rods on the left rear the rod is bent at rear close to the backing plat. the one on the rt is straight. before i straighten it i want to be sure that it is not to be bent thank you kevin

hello As you may know by now i am doing the brakes on my 30 two door. t replaced everything in the frt brakes and used the flat head ted deluxe kit. On one side the arm is still vertical. The other is 15 degrees I used new wedges and new brake rods what do i need to look at before i put pills...

hello i am putting on my rear brake arms on the roller track i took photos but not very good ones dose the flat side go towards the backing plate or dose the taper side? thank you kevin

hello i may have a clogged vent hole in the shift tower. how do you check it and clean it? do you have to pull the shifter to clean it? thank you kevin

hello i have been working on my brakes i am replacing the bearings on the frt. the hub inner bearing seal i can not get it off the backing plate,spindle . what it the best way to remove the old one thank you kevin 1930 tudor

hello i am still working in my brakes. on the rear i have the two square pins on.and two things are happening. i have the backing plate off the car. i replaced the roller track assy. i thought i would test the adj of the pins and i can not get them to turn. i took it back apart and they turn...

hello I am working on my brakes i am gett ready to put on a flat head ted kit. I want to check the rear roller to be sure it is good before i install it. what do you look for to see if they need replaced? thank you kevin

hello i do not know if i will understand how this is put on my brakes the instructions are for someone that knows how to do the brakes there was not a parts list so i don't know if it is all there and no parts description so i don't know what part is what so i don't know if i just got...

hello i am working on my rear brakes i need to get the e brake backing plate off to get to the brakes i have everting loose but the backing plate will not come off i do not want to bend it i do i get it loose with out doing damage to it this is on a 30 tudor thank you kevin

hello i am getting ready to do the brakes on my 30 tudor i am still waiting on flat head teds deluxe kit i have been reading a lot on how to do this. i see that there is a lot mentioned about arcing brakes but could not find out how to do this or what is means any help thank you kevin

hello my Bendix broke and the local vender had only the modern Bendix I can not get it in the starter hole what is the trick looks lik I have to remove the water port on the side to line it up to go in is that correct kevin 1930 tudor

hello we have a 1925 model t we are getting smoke from where the throttle rod pass through the engine to the carburetor it is real bad we thought it may be the head gasket but no water in oil any ideas thank you kevin

hello I was getting a unusual noise from my eng when driving . I was cking the oil and saw I was missing a oil pan bolt. when I went to replace it. I found that there where two missing and the rest were loose I fixed it and now the noise is gone. possible the oil pan was fiberating I don't know...

hello dose anyone have a photo of how and where they bolt on to the frame I got the spring type did a search did not find much info or photos thank you kevin 1930 tudor 1923 todel t roadster p/u