Search results

So just recently have parted ways with my 38 Barrel Nose. Replaced it with an Australian 1951 Ford Twin Spinner, coupe ute. Was rebuilt approx 10 yrs plus in Australia and imported by previous owner, who I know some 10 yrs ago. Going through a few things and the 8BA engine is running the 8BA...

55 Customline 272 with manual and o/drive. Works very well in all areas ie in and out etc. Some time ago replaced in/out cable. The only area which has not worked since I've owned it is the kick down switch at floor location. At this stage thought it would be good to have it operating. Do have a...

38 PU still running 6v positive earth. Checking out irregular horn operation. Sometimes works, othertimes no or weak sound. Have checked all connections all seem ok. Now have found that the horn relay is a 12V one. Could this be my problem area. Not enough voltage to pull in the coil to supply...

Running 272 Y block on 12v. Still had 6v starter motor which gave up!! Followed some posted instructions on this site or the other 272 Forum. Dont forget this is a RHD with steering unit(power Steer} in the mix. released the mount bolts RHS LHS just slacked off a bit. This was enough to remove...

So have a 55 Customline Y block 272 running Pertronix Ignitor 2 Ignition fitted to originsl Distributor. Presently have Champion F11 Yx plugs fitted. Any advice suggestions on running other brands as usually go with NGK plugs. Thanks Phil NZ

Originally Posted by KULTULZ View Post You can, but if the fuel section diaphragm is damaged, gasoline may be pumped into the crankcase. And you would possibly need a fuel pressure regulator also. I would rebuild the pump - https://www.then-now-auto.com/fuel-p...fp-kits-single If you...

Hi I am located in New Zealand and would like to get assistance with oil resivoir filter dimemsions. Height, ID and OD of filter. Shipping from US to NZ expensive. Hoping to pick up a filter locally which can fit this position. Presently nil filter is fitted! Dont want to continue running...

1955 Ford Customline has been fitted with new rear springs. Previous owner had this work done. Looks ok maybe still sitting a little high. Can any body give the ride height, as taken from centre of rear tail light to ground? Many thanks in advance. Phil NZ

Will be purchasing a 55 Ford Customline fitted with overdrive, factory. There is a spare gear box with the car. Would this gearbox work with this set up provided this spare gearbox is a stock one? Appreciate assisstance. Phil NZ

1938 Deluxe Coupe with original fitted shocks. Have unmounted left rear shock to check operation and adjust for stiffer movement via the needle valve adjusring screw. Looking at this shock in mounted position the firmer adjustment is obtained by turning adjuster screw towards the front of the...

Recently attended annual Hawskswood Hill Climb. The 35 Coupe has been around for many years and was running in Sundays event. 39 Coupe was the backup/support team, thats me. This picture taken just off main road. This small garage has just reopened again after many years shut. In its past life...

The rear seat back support has a curve at top support outline is strengthened with a metal strip. See picture. This being on LHS on RHD car. The purpose for this shaped piece is ?? Must be a reason or else it would just have timber straight across? thoughts? Thanks Phil NZ

Have just aquired a 38 Deluxe Coupe and lloking for info or pics on securing device for spare wheel. The spare wheel sits horizontal at aft end of trunk. There is a small right angled pivot piece which obviously requires more bits to secure spare wheel. This is new to me and dont have any idea...

So have a 99a Engine I have been playing with. Presently set up to run on engine stand. Had made up a timing pointer and fitted when I had heads off to check. Its fitted with a crab type distributor. So couple of questions on checking timing. Moving side adjuster plate clockwise advances timing...

Have this C I inlet manifold as per pics. On top there is a marking F3 then a marking K 23 S or K 23 9. this one hard to see. The slots at inlet side LHS these are for vaccum line connections at top side for wiper and distributor? . Appreciate help to ID year. Thanks Phil NZ

First time for everything and so here it goes. I'm playing around with a spare 99a Flathead engine. On setting the valve clearances to specs of 10 thou inlet and 12 thou exhaust. I noted that on turning engine over the valves on a few cylinders were sitting off valve seats by approx 10 to 15...

Hi just to show these vehicles can still be used for what tey were made for. Been getting rid of a wind blown pine tree. Ideal for the job. Enjoy using these as they wre originally intended for. Its running an 8BA flathead with hydraulic brakes. Phil NZ

My query being: Will doors off a 39 Ford standard sedan fit a 39 standard coupe? Or is there some work required? Understand there may be work required around top edge of door. Appreciate any advice on this one. Thanks Phil

Earlier this month sttended a car show at Reefton. Open to all types of cars. These pics are of the true blue flathead powered vehicles fire engine included. A good day out. Phil NZ

So recently acquired 39 Deluxe Coupe. Window winders not fitted. See attached picture. My question is does the smaller round piece sit atop the larger piece or does it sit inside it. On backside of smaller piece are 4 small tags which line up with the holes in larger piece. Appreciate all advice...