Search results

Nice clean set of heads from a rebuilt engine. Engine ran great I replace the heads with aluminum ones. casting no on each 77-6050-a Ford logo is indented. Also have the intake.

I have been collecting parts for this project for almost 10 years. I have a beautiful original uncut unmolested early 32 frame. V8 rear end. Uncut front wishbones with either a early dropped A axle or an undropped 32 heavy. 40 brakes. 32 stearing complete including stearing wheel and drop...

I have a very nice set of 21 stud heads and intake removed from a recently rebuilt 1937 engine. The engine ran great I replaced them with aluminum parts. 586 524 4198

Original engine trans rear end. Dropped front end. Lowered rear x member to lower the rear. Converted to lincoln Brakes. Original wide five rims with new tires. Custom duel exhaust. Original interior, all guages work. Not perfect by any means and needs a couple of thinks fixed at the...

I have about 300 miles so far on my pick up with the stock 21 stud engine. It has ford aluminum heads but otherwise stock. This week end I identified the rattel noise I was hearing as spark knock. Sounds very similar to my old corvette with high compression engine when it didn't have enough...

Can I use the later style fuel pump with the sediment bowl on my 21 stud engine. I had some debris in the tank when I got the truck and want to monitor what's coming out. I have an after market inline filter on just before the pump now but it looks like crap with the stock engine. Thanks.

Ordered a new knob and it is not like the one on my truck. It has two mounting screws and is rectangle shape. The knob on my truck is round and installed permanatly with a rivet type fastener.

I orderd seals for the door bottoms on my pickup and they are different than the ones that were on the truck originally. The ones they sent go into a retainer on the bottom of the door, the ones on the car were held on with clips. The book shows 35-36 with the holes for the clips. My doors...

Looking for a set of usable support rods for my 1937 ford pickup. They should measure 26 inches in length. All the repo ones I have found are universal mesureing 32 inches and there is no thread at 26 inches where I would have to cut it. Plus they are stainless steel and slightly thicker in...

I'm putting the fenders on my pickup and the board doesn't meet the rear fender. This is a glass running board that came with the truck. I'm hoping they might be a different year or something. They measure slightly less than 53" . With the rear fender in place there is a 1" gap between the end...

Ok I fix one thing and something else pops us. Sure glad we have message boards these days:D So I changed from the stock cast iron heads on my 21 stud engine in my 37 pickup to the factory aluminum heads. I used a coper clad gasket that was recomended. Sprayed copper gasket sealer on both...

I just changed from a cast to an aluminum intake on my 21 stud engine in my 37 pickup. The aluminum intake is shorter at the fuel pump mount so I purchase the shorter rod to compensate. Well it didn't pump any fuel. So after inspecting it I see the small shield is not in the same location...

Getting ready to put the Ford Aluminum heads on my 21 stud motor in my pick up and need the tightening sequence. Also not sure on the final torque either. I searched and found it for the 4 banger but not the v 8 and also wondered if there is a difference for cast iron and stock ford...

I got the new knobs and rods and gromets and now have a couple of questions. My pickup didn't have the original knobs and rods in place so I would like to know how they actually attach. The knob has a short piece of rod that goes through the dash gromet of course. And the new rod came with a...

I have a set of factory ford aluminum heads for my 1937 21 stud engine. I see copper gaskets listed in the parts books along with standard head gaskets. I was wondering which ones are recomended with aluminum heads or if makes a difference. Thanks

Nice 1937 Ford Pickup. Built as a fenderless hiboy style. Functional Belly Burner exhaust. Nice paint. Lots of new stuff. See link for larger add http://www.jalopyjournal.com/forum/showthread.php?t=635236 message or call Rudy@ 586-524-4198 Thanks.

I have an original heater from a 40 ford I want to use in my 37 pickup. The truck is still 6 volt so I didn't think I would have a problem witht the one I have. When I went to hook it up I noticed there were 4 wires coming from the motor and they were cloth covered and covering was rotting and...

Determined the Carb on my flathead is leaking internally so I want to just buy a new/Rebuilt/remanufactured carb. See lots of sources on line and have heard stories about new ones that so and so sells. I am actually going to run two on my engine. Don't trust the one I have to rebuild, had...

Like the title says I would like to find a usable pair of aluminium heads for a '37 21 stud engine. I know they are few and far between and I expect to pay a premium for a nice pair. Pm me,Thanks.

Just like the add stated. I am looking for a dropped axle for a 37 ford pickup. I'm sure it is the same as car. I would like an original that has been dropped. Rudy 586 524 4198