Search results

Is any company or supplier reproducing the stainless trim that goes on the 40 Ford deluxe steering wheel? I've done some searching but haven't found anything yet. Any help would be appreciated. Thanks.

Looking for a set of F250/350 hubcaps from 67-77. They look like the picture below. Send me a message on here or email modelafords@yahoo.com if you have a set, will consider individuals if you have them in good shape. Thanks.

Looking for a set of brackets that bolt to the cab which the inner fenders bolt to that holds the front clip on. Let me know what you have. Thanks.

I was looking on shorpy.com this morning, it's a good site for old pictures if you never been there. Anyway I came across an old picture dated 1932 with a bunch of old cars. This one car has me puzzled. It looks like it's a model a but its not. The bumpers look like the model a from what I can...

Has anybody retapered a set of 32-34 Ford tie rod ends to allow the tie rod to go below the wishbone? If so how hard was this to do? From what I've found it's a 7 degree taper. Do you think a typical machine shop should be able to do this? Pics and info would be great. Thanks.

Need a passenger side inner fender for a 67-72 Ford truck. Must be solid.

Does the drive gear inside the transmission on the shaft supposed to slide or is it supposed to be locked in place at all times? Mine slides after removing the speedometer driven gear that the speedometer cable goes into. I'm thinking the clip is broke that holds the drive gear inside the...

I have a 39 style transmission with the 3 inch shift fork. It came out of a 41 pickup. I've been running it a few years and went thru it before installing it in my coupe. It's setup for open drive and comes with the clutch disk. I Recently switched to a T5 transmission in my coupe so I have no...

Ansen Intake with a Stromberg 97. The intake is almost new. Bought new, less than 100 miles on it. Switched the motor out years ago to a V8 and didn't need it. The Stromberg 97 was rebuilt a few years ago by Ken here on the fordbarn. Smaller jets were installed to run with a model a or b motor...

Two rear fenders for coupes, pickups and roadsters. One is a 29 and the other is a 30-31. Both are solid but some dents, dings and repairs. Both are down to bare metal so nothing to hide behind paint or primer. Some body filler to fill in the dents and dings. Asking $50 each or best offer...

Question as to why or what would cause this. Running a 41 pickup transmission in a Model A coupe. It's behind a stock 283 Chevy, never had a problem before. Took the car out for a spin today and went to shift from 3rd to 2nd and couldn't get it into 2nd or any gear other than 3rd. Couldn't even...

Does anyone know the part number or have a link to the clips that hold the cowl band on when using a early 30 tank with a 31 cowl band? The early 30 gas tanks didn't have the rib to hold the cowl band on like the later tanks. Any help would be appreciated. Thanks.

Looking for a passenger rear fender for a 31 coupe. Looking for one that hasn't been repaired or out of shape. 30-31 coupe, roadster and pickup fenders are all the same and will work. Must be willing to ship or within a couple hours driving distance. Thanks.

How close or tight should the rear fenders on a 31 coupe or roadster fit to the wheel well and body? I'm doing some body work on my coupe and in the process I've stripped down the rear fenders to bare metal only to find there was lots of bondo on the fender that filled the gap to the body. The...

Hey guys, I'm doing some bodywork on my 31 coupe. The usual patch panels and touching up some ruff areas. I need pictures of 30 and 31 coupes in two areas. One is were the windshield post, visor and roof meet. On my coupe there's a small gap or hole on each side, it's about the size of a pinky...

Couple questions on a 39 transmission. How much gear oil does it hold? Mine has a leak at the drain plug, I took the plug out and wrapped it with pipe tape but it still leaks about a teaspoon or so every couple days. I always fill it thru the shifter tower because it's in a Model A coupe and...

Working on my somewhat modified Model A. I'm running into a slight rub problem when turning the steering wheel at full lock. My question is would it be possible to reverse or turn the tie rod upside down and still be safe and functional without hitting the wishbone? What I'm asking is if I was...

Trying to figure out something with a 32 grill and hoping for some help from others who have done this. I'm running a 32 grill shell on a 31 Model A with a 31 Model A hood. The problem I'm having is the center hinge of the Model A doesn't fit with the front 32 hinge mount on the grill. When I...

Does anybody know what model car or truck theses horns came off of? Any help would be appreciated. Thanks.

Looking for a 1932 Ford headlight bar. Doesn't have to be perfect. With or without the V8 logo. Will be going on a driver. Send me a message here or email modelafords@yahoo.com Thanks.