Search results

The 40-8620 fan belt I have is just a little bit too small for my engine. Does anyone know what the next size up belt would be? Tried to go to local Advance auto parts store , but they are unable to help or measure my belt and find the next size up. Thanks

I am new to the V8 family, been doing model A's for 25 years and always used Felpro copper gaskets with Permatex copper sealer. Now I am reading about using grease, is this because of aluminum heads that expand more then cast iron heads? Just wondering as I am getting ready to reassemble the...

I want to remove the cowl on my 1933 Station wagon, so I can sand blast and paint it, but can't figure out how it comes apart. Has anyone taken a station wagon apart? Thanks

I am looking to have my gas gauge in the dash refinished. The speedometer and amp gauge are fine, but the red dye seems to have faded the gas gauge. My hope is that I don't have to redo all three gauges. Thanks

Can someone point me in the right direction for the paint formula to Mountain Brown a 1933 commercial color? Thanks

This sounds like a stupid question, but can someone tell me what kind of finish did the aluminum heads have from the factory? was it a high gloss , a dull gloss , or a flat finish? Thanks.

Any suggestions for a rebuilder of a 1933 Detroit lubricator carb?

Was there any other color available from the factory besides tan for the 1933 station wagon? was it the same color as a 1931 wagon, or darker brown? Thanks

Car is in New Jersey, Selling for a friend ,no title only bill of sale. Car has been in old garage for several years. Motor turns but not run in years. Sheet metal in good condition. Upholstery has a few holes from mice. Text phone number 201-919-3378 for pictures.

Can someone help me out with how the brakes are adjusted in my 1933 station wagon. the brake pedal is resting all the way to the floorboard. when I climbed under the car I see at the cross shaft has a sliding end on the rod from the brake pedal. There is a clevis pin which allows the rod to...

There is a open coil resistor under the dash that is rusted and broken. The former owner has a jumper across the two ends. What is this for ? I found a wiring diagram that leads me to think it is for the ignition coil. Thanks

. I have an April 1930 Murray Fordor sedan. It was restored in the mid seventies. Engine runs well a compression test shows 70 on each cylinder. Interior is in good condition with a few small holes, original headliner, rear shade, horn and wiper motor. I have a clear NJ title. There are a few...

I found the initials NK686 stamped into the wood sill of a 1930 Fordor sedan.Is there a list of the factory initials that would tell me where this car was built? Thanks

I have a April 1930 Murray Fordor sedan. It was restored in the mid seventies. Engine runs well a compression test shows 70 on each cylinder. Interior is in good condition with a few small holes, original headliner and rear shade. I have a clear NJ title. There are a few scratches and chips on...

What size screws are used to bolt the top bows to the roof ?

I have an early March 31 S/W and the Front door window garnish has 3 screws on the front inside edge and 2 screws on the glass side. I am helping a friend with a late 31 S/W 160 B and his front window trim has 2 screws on the inside edge and 2 screws on the glass side. Could the difference be...

Are the 28-29 headlight sockets longer or shorter then the 30-31 sockets? I know the focus screws are a different length but not sure which sockets are correct for 31. Thanks

Going to and coming home from Gettysburg I had a problem with the engine overheating. We traveled 160 miles and a lot of it was at 45-50 MPH. I noticed that if I opened the GAV adjustment 3/4 to 1 full turn that the temp would come back down to normal, but when I came to a stop the engine would...

Dose a multi disk clutch get as much pedal play as a regular clutch would? Thanks.

A club member has two 1/2 by 3/4 inch rips in the top material. He has extra material from when his father installed the hood over 20 years ago. I am looking for a good, flexible glue that some one has had success with. The holes are right at the top bow. Thanks for the help.