Search results

1 Lot of door latches total of 14 pieces There are 4 original door latches from a 1935 Ford 4 door convertible. There is also 10 latches machine from solid steel billet there were left over from my build. I used the machined ones for more adjustment and alignment. Email me

Brand New Set of aluminum flat head V-8 heads Made of todays aluminum alloys from Kearney Foundry in California. Head and water pump gaskets included. Available right away! I can deliver to Hershey to save on shipping

I did a restore on a 1935 4 door a few years back. When I acquired the car it had on it cast iron head not aluminum. Not knowing any better when I had the engine done I left the iron heads on. I have now acquired new cast aluminum heads and want to change them out with the iron heads but keep...

What type of gas should I be putting in the car. I have leaded available in my town but now sure what octane it is. If it doesn't matter and I use unleaded what octane should I use? Can I add STA-BIL to it? thanks for your input

Was the Standard air breather cap (the scoop with the screen) gloss or flat black. How do you install the NEW 5 point wire screen (chicken fence) and copper mesh with out killing your hands and scratching you air filter:mad::confused:

Looking for a tool kit for a 1935 4 door convertible, also looking for wrench and lower instruction book. Owners manual too. Email is quicker for me then PM Thanks Tom

Is there anyone who sells a complete tool kit for cars?

Don't laugh to hard at my picture, this is the prject 12 years ago before it was torn down. It really smelled and my daughter hung the sponge bob air fresher inside the car. Anyway...is this correct the way the vacuum line comes out of the trim panel above the windshield? Does a gourmet go in...

Ok I am trying to get two new horns wired up on a 1935 restoration. The wiring harness has 6V to ground on the two yellow wires on each side. On the Blue Yellow wire I get a short to ground when the horn button is depressed and a break when it is released on both sides. This Seems correct to...

Looking for an original wiper motor (heart shaped) for a 1935 4 door convertible :( Any leads on one send me a PM thanks Tom

Can someone tell me where this two braces go? I had them in a box with my headlights and horns so I assume they go somewhere in the front fender:confused: many thanks in advance, send picture if any are available.

So I had coolant coming out of the head from porosity of the casting. Everyone told me to buy BarsLeak and use that to fix the problem. It was against my judgment to do this but I did and it seems like it worked. So now I have new question the radiator cap??? It not like its a pressure cap...

Just got my 35's engine running again after 5 years since it was rebuilt. After running it for at idle for about 5 minutes and building some heat in the motor I noticed steam coming of the engine. Looks like the head cover is crack or has porosity :mad:. Need help on: Thoughts on...

Chocolate Field 4-Q-19,20 I will be selling assorted parts left over and not used from a 1935 restoration. I will try to post a list in a few days.

Looking for a mechanic that would be willing to come to my house and help me get my engine started and running smooth. I have been working on a ten year restore and did get the car running about 5 years ago, I think before I started the body work. Now all the body work is done, dash is in and I...

Looking for seat adjusting rods for a 1935 ford conv. I can alter if needed, so anything close would work Send PM or email Thanks Tom

Can anybody show me a picture or describe on how the welting ends on the front fenders where the meet the cowl and running boards of the car? another words the back of the front fenders. Thanks in advance Also looking for a set of front set adjustment rods.

Finally getting to some fun stuff on my restoration Cigar lighter and Instrument light switch, I have the original socket of the cigar lighter (not sure if it works) and the original instrument switch which does not show any continuity in either position. Any thought on what to do to replace...

Does anyone have a picture or dimensions of the retainer that fits in with the toggle switch? I also need dimensions or pictures of the ball and spring that fits under the screw. Any help is much appreciated. Thanks

I feel so stupid doing this post, I realize I am not the first person ever to do this and I guess I won’t be the last.:( I took my ignition block apart thinking I would be putting it back together in a month. Well a month has turned into 8 years and of course I have problems finding...