Search results

1939 ford model 78 trans case. Case is empty, no cracks. Bearing surfaces look good. $125 plus shipping.

Nice 1939 ford transmission tower. 91A with the 3” fork. Very nice shape. SOLD

Main shaft, speedometer drive, and rear tail housing/bearing retainer. Convert your closed drive trans to open using ford parts. $200 plus shipping.

Yankee self cancelling turn signal switch. It does go back to park when you turn the wheel. $65 plus shipping. Thanks.

Model A chassis. No engine/trans. What you see is all that is there. Pickup in Romeo, Michigan.

Ford 9 inch rear axle. It measures with the drums off approx. 57.5” axle face to axle face. 50 1/4” backing plate to backing plate. Could be a ‘58 wagon rear axle. It would need to be gone through.

Looking for 1957 F-100 hood emblems and the V-8 grill emblem. Driver condition preferred to match truck. If you have any for sale please let me know. Thanks.

2 wet “ish” plugs Been driving my ‘36 LB for almost 5 years now and I noticed a very slight miss at idle recently. I do not know the history this engine as it was given to me by a shop owner that replaced the cars entire drivetrain with new. I inspected it and had the heads off. I is sleeved on...

Back trim for headliner on early 35 pickups and driver side windshield garnish. Parts were pitted and have been repaired but they would like fine installed or they could be taken further. $50 plus shipping

My horn recently is on the fritz. I have the cover off and oiled the bushings. If I rotate the motor by hand a little and hit the button it works. If I don’t slightly rotate it by hand though it does nothing. It spins just fine when it does spin. Could this be brushes going bad? Connections all...

Left over parts. Rear cab section has good cab corners. Front has a decent cowl, firewall is gone. Good for patch panels. $150 pick up only.

Looking for an original pedal pad or a pair of they are the same. Bringing an old race car back from the dead and need one for the passenger side. Pic is one I have on driver side. Any help appreciated.

Working on a ‘36 truck for a customer. It came in pieces and I am just starting to test fit panels after lots of rust repair. The radiator does not have any mounting provisions for the grill. Is this normal or has somebody cut off the mounting area?

Does anybody have a really nice cab that has had no damage to the vertical braces that go from the window opening to the floor? I had to remove them to repair the bottoms and actually took one from another cab that was in better shape. Are these flat or is there a slight curve in them? I see at...

We’re offset dovetails from the factory? I recently bought what I was told was an NOS set and one was not centered. It actually worked better than the one that was center and made my body lines spot on. I understand the hinges take their toll as well as the weight of the door over 80-90 years...

‘36 pickup inner door bottoms? Hi guys, I have two doors here and both have really bad inner bottoms. I have looked and I cannot seem to find a vendor that carries the inner door bottom although I have seen pics where it looks like they are available or atleast they used to be. Does anybody...

I have had a few 35 trucks but noting ever nice and nothing had the firewall pad still in it. I just replaced (temporary in place) a botched up firewall on a ‘36 cab and the donor firewall had 13 of these bolts. They look like they held the original pad on. I count that I need 16. I have 13. Is...

Hi guys, My step father has a thunderbird with the overdrive 3 spd. Is this a rare trans? He wants to update the drivetrain and is wondering if this trans is worth putting up for sale. I have no experience with these cars or that trans so when he asked me I came up empty.

‘36 1.5 ton front fender brades The truck I am working on is missing the lower front fender braces. They attach on the lower side of the fender. Does anybody know if they are the same as 1/2 ton? Thanks.

Looking for a good roof/top for a 35-36 pickup. I have two cabs here and both roofs are damaged severely. Looking for something that has not been hit. Location doesn’t matter at this point as long as you are willing to put it on a pallet. Thanks.