Search results

Hello All: I have done alot of searching, thought somebody might have a definitive hard number that would save a bunch of measuring: What should the Fuel Pump pushrod length be for an Edelbrock Slingshot on an 8ba with the 8ba Fuel Pump? Already have crankcase ventilation set up w PCV and...

Hello All: Posted this over on the HAMB too (got some good insight, just wanting to see if anyone here has ever actually run one)- has anybody used the Odyssey PC680 w a generator (12V)?? If so, any issues?? Thanks in Advance, Dave

Very nice Edmunds intake w 2 very nice Stromberg 81's. Pulled this off of my running car a few years back, I would go through the carbs. They are move freely and are very clean. Includes linkage and fittings as shown. $750 Best, Dave

Very nice patina- $95 shipped to lower 48. Thx! Dave

Hello All- in looking under my 34 project, it looks like the bolt and nut attaching the radius rods to the torque tube are incorrect (no cotter pin). I have the correct bolt, nut, and cotter pin- my question is, how tight when I switch fasteners?? Thanks! Dave

Whelp, I thought I had everything perfectly planned, my Flathead newbie status was just exposed. It appears as though the I have a long snout cam and my 2 bolt timing cover won’t allow the distributor to index properly. I don’t want to swap cams. I guess I can put a 3 bolt cover on it, and use...

Hello All: I just want to make sure I have my ducks in a row- I have dressed the front of my 8ba with early pumps, cam, 2 bolt timing cover, pulley, etc. I am going to run a stock rebuilt crab distributor, w vacuum brake. I need to run vacuum to the manifold from the timing cover, what is the...

8ba "Inner" Road Draft Tube found thx Hey Guys: I need the "inner" 8ba road draft tube- the piece in the valley. Thank You! Dave

Hi guys: What is the best way to remove the inner part of the road draft tube (in the valley)??. I tried grabbing it with vice grips, it doesn't seem to want to move. Thanks in Advance, Dave

I need an original coil bracket crab type ignition Thanks! Found one thanks

Hi All: I am about to swap my tired 59a for an 8cm that I have put together, with early front dress (cam/ cover/ water pumps/ pulley/ crab/ etc.) I have the truck bellhousing for the later motor also. This will be going in my 34 5 window. I will be running my existing 39 trans- couple of...

Looking for a nice solid driver side door latch. Feel free to message me if you have one available. Scammers need not apply- Thank You! Dave

Hi Guys: I have a new left over 59a lower front oil pan rope seal that came with a pan gasket set- Will this work on my 8ba oil pan?? Also, no trim on the front, top and bottom, correct?? Thanks All, Dave

Looking for four 16x4 or 16x4.5 wheels. Looking for straight, clean for paint. I am in Houston Texas. Thanks, Dave

Looking for a solid door. Don't bother with me if you are a scam artist! Thx, Dave

I have been scammed. I posted an ad in the want ads and was messaged by jackdennis4679 that referred me to an email indicating that he knew the part was available. I was looking for the elusive late flathead merc oil pickup. The whole exchange didn't seem right, but I was super busy at work and...

Looking for Merc Specific Pickup for Pan w Windage Tray. Thanks, Dave

Hello All: I have read through a few of these threads, need some input on what I have: 4 inch stroke, 3 5/16 bore w/ Ross Pistons, Brand New Navarro Heads and New Best Graphtite Gaskets. New ARP Studs. Aluminum Foil at sides and center of piston- torque to 40 lbs: Clearance Middle = .120...

Any problems adding valve spring shims to the retainer side? I don't want to stack too many on the guide and lose the spring register. Thanks! Dave

I know there have been numerous threads on this topic, here is my question: Is a 59ab from transmission mounting surface to water pump mounting surface the same length as an 8ba with the bellhousing bolted up- Transmission mounting surface to water pump mounting surface? Thanks Guys, Dave