Search results

Running a '48 59AB in my 36. Have a fairly new mechanical fuel pump (not sure where made, but it appears to be a good quality pump). I have a formed hard line between the pump and Stromberg carb and a fuel pressure gauge t'd off it. Seems it used to run 2-3 psi last fall, but now is down to 1...

1935-48 Ford 6-Spline V8 Banjo Rear End Open Drive Conversion Kit. All parts like new. Speedway #9191105, $286 new. Ran less than 1000 miles and went in a different direction with the car, banjo rear ended up coming out. The paper gasket for the housing is missing but you can use gasket...

These came out of my 36 five window. I’m guessing they were reproductions, but I don’t really know. If anyone needs them as a template, I’m happy to ship them at your cost. I’d suggest cutting them in half cleanly to make a smaller size package. If someone wants them as is and really wants to...

After a few months, most bugs are worked out with my 36 coupe. Runs great, good fun. One challenging issue is a pesky drivetrain vibration problem. As speed increases this becomes more and more noticeable. I am running a T5 trans, new professionally fabbed driveshaft, '36 banjo rear, transverse...

I’ve got a set of 4 16 inch tires sized 195/80R16 in like-new condition. 15 years old, so not too trustworthy, but great for sizing check, roller, or car you drive very little. They are narrow and tall and were on my 36, pretty close to the original tire size. Obviously local pick up is...

I did some searching on the forum as I troubleshoot a problem with my 59AB, but looking to more savvy flathead folks here to help me solve this issue. First, everything is essentially new on this H&H built motor that I acquired. I am running 12v negative ground. All new wiring. All new fuel...

Will this type of 49-53 intake manifold work on a pre-49? Presuming that I would maybe need to block off the 8BA oil fill hole? Or could I use it on my 59AB? https://www.speedwaymotors.com/Speedway-1949-53-Ford-Flathead-V8-Dual-Carb-Intake-Manifolds,184019.html Thanks! Pat

I have removed all my interior door trim to replace a cracked door glass. Is there a procedure published by Ford to properly remove and replace the glass, or can anyone provide insight or instructions to complete the job? It doesn't look too complicated, but always good to know any tips or...

I’m reassembling my 36 and looking for confirmation on correct front fender welting. When I disassembled, there were 3 pieces on each side of black welting with a stainless cap that aligns withe the fender joint. There was no welting on the inner rear part of the fender where it bolts to the...

I have the original interior panels from my 36 coupe (or very old reproductions), which are like a heavy cardboard material (not corrugated), black or natural color on the backside and maroon/red on the visible side. Mine are broken and in poor condition. Searching online has produced no...

My 36 has an original type brass radiator, which currently has a chrome or nickel plated cap with a paper type gasket (which leaks steam readily), and an overflow tube from the upper front center of the radiator which appears to be open to atmosphere. Did the 36 originally come with a...

Just sharing some info as I finish up details on my 36. I needed a front turn signal solution and preferred LED and inconspicuous. Found these lights, I think on Amazon; the measurements provided were close so I took a chance and bought a pair. They could not have fit any better. See photos for...

Nearly new fan belt off my original 36 coupe 21 stud engine. NAPA 25-24562 installed 2 years ago with under 100 miles on it. I'm running a 59AB now and this one doesn't fit. $8 plus shipping Thanks, Pat

New in package 1935/36 all, Battery to Starter Cable with Bracket #48-14300-B. $35 OBO plus shipping Thank you, Pat

For sale new in package Dash Wiring harness #68-14401 for 35/36 car and pickup. $110 OBO plus shipping. Thank you, Pat

New in the package headlight and tail light wiring harness #48-11647 with rubber unions. $100 OBO plus shipping. Thank you. Pat

I've just finished wiring a new custom harness and fuse panel in my '36, and have asked a few questions here. Responses, as usual, have been very helpful. Next question: First, some background. I have a 12V, negative ground system. All ignition power except the coil feed is going through a...

I am just finishing up my project and getting ready to for a first start up, etc. Currently working on finalizing the fuel line connections. I have 1/4 hard line from the tank to the firewall, secured by the metal clamp on the firewall. I have the Ford stock rubber hose with flare ends to...

I’m building the wiring harness for my 36 coupe, which is 12 V negative ground. Stock flathead powered, power-master alternator and starter, and electric fan via a fan relay. Headlights TBD. Also an under-dash Arvin heater with 12v fan. I’m guessing with 12v power my current draw across the...

Max. current draw across stock ‘36 ignition switch? I’m building the wiring harness for my 36 coupe, which is 12 V negative ground. Stock flathead powered, power-master alternator and starter, and electric fan via a fan relay. Headlights TBD. Also an under-dash Arvin heater with 12v fan. I’m...