Search results

Is there a way for a simpleton to tell the difference between detergent and non-detergent oil? Would like to know what is now in my A. Thank you, Nick

Have installed a repro spider using existing switch plate and switch body. The tabs on the spider are not engaging the switch plate slots even when tried off the column; and when installed in the column the lever at the steering wheel goes around 360^. Do you think it's because of a repro spider...

Obviously want to go the easiest route on trying to change my light switch rod. I have a '28 Coupe, is there a way to lower the column just enough to get rod in and out inside the cab so that the column doesn't have to be completely removed? In the photo couldn't I just remove the bolts from the...

Finally got my horn back in action but while testing the horn button (which worked) I decided to move the light switch for a little test. The lever never engaged high, low or parking lights. It moved around 360^ and none of the lights came on. What's my new project this time?

So I ordered a fuel line replacement from sediment bowl to carburetor from Snyders a week ago, finally arrived, went to install and noticed the ends weren't flared to hold the line from being pulled out. I wouldn't think I would have to put my own flare on the ends, if that was the case I...

Does the metal flex line running off the oil filler tube need some kind of screening at the bottom to prevent dirt, sand, road debris from getting sucked back into the engine? I see signs of sand/dirt particles on the inside wall of the filler tube. Also, is the flex suppose to be supported...

Want to replace fuel line between sediment bowl and carburetor, is that made of anything special or do I just use 1/4 copper or brass? It's hard to tell what kind of material it's made of. Also what fittings will I request at the auto store or does the fuel line and fittings come as a kit...

Have been having troubles with carb., cleaned it twice. First time car fired right up--2 days later wouldn't start; cleaned it again and installed inline filter between sediment bowl and carb, fired right up, ran for 5 minutes or so then started to starve for gas, then died. Now won't start, it...

Another darn horn question--took it all apart, cleaned it up (armature, brushes etc.), replaced gaskets, put all back together and guess what? You're right, it doesn't work! Read 6v from one connector on the horn to frame; but when I connect hot leg to horn and then ground other connector to...

Two questions: 1)Friend was over assisting me on installing and inline fuel filter to contain sediment ending up in the carb causing starting issues. After we got it running he noticed the fan belt loosening slightly, there is one mounting bolt location. Is this correct or are we missing...

Posted a few days ago for horn diagram with great results, thank you. I have now received a few parts I ordered and proceeding to put it all back together. One question, the gaskets were missing and I am putting new ones on---do the new ones need any lubricant on them? It may be a dumb question...

Ok I've decided to try the "California shake" :D on my fuel tank to try and get whatever is clogging up my carb (sediment I assume). Anyway, have read all the threads and being new to this whole Model A thing I want to eliminate costly mistakes as I proceed. I have read the mention of putting...

Want to remove the connectors where the conduit meets the headlight body and run wiring inside for soldering the connections. Does anyone know of a rubber grommet I can use and if so how would the conduit be held securing in place (photos would help)? The opening at headlight body in 7/8 and I...

Have read many posts about gas tank cleaning but I haven't seen anything about the need to remove and clean spark arrestor in the tank. I am have tank debris issues and happened to shine a light down in filler and the arrestor looks all "gunked" up. Any thoughts and any photos? I will try to...

Going to attempt to clean/service my horn. I have searched the Barn until my eyes burn but can't seem to find a parts diagram and a condensed version of I should do for just cleaning and servicing (not rebuilding). By the way it's a Stewart Warner horn. Thank you for your help.

Hello All, Ok I bought this '28 a few weeks ago and have had nothing but problems right off the bat. This is my first post but have been lurking and searching trying to find answers unfortunately my mechanical abilities are limited and at times feel overwhelmed with reading all the threads while...