Search results

Putting the rear end back under my 34 and it had the stock rear spring u bolts still in place. Using the stock 10 leaf spring and rear end. The clamps or brackets that slide over the u bolts is what I’m having problems with. The ones I have are to narrow and the one set that fits stud spacing...

I need a model a part picked up until I can arrange transport . Seller needs it gone . He’s in the oak lawn area . Thanks

Looking for a front 35 brake drum . It has 5 cut outs with a rib around it . Thanks

Hi , I’ve read some post & the frame welting goes on the frame then the splash aprons. The front body block under cowl the rubber shins go between the bottom of cab & on top of the apron correct ? On The center & rear cab blocks are the rubber shins nailed to the top or bottom of the wood...

Hi everyone. Has anyone used the logo lites brand led headlight bulbs ? I do as much night driving as daytime & a lot is on back country roads. My 29 ccpu has a stock 6v gen. Wondering about the brightness & the lifespan. Want a good headlight but not the sealed beam or halogen. The led draws...

Has anyone here used the top wood kits from little Dearborn ? Site says made from hardwood just wondering how figment is. Most suppliers are 5-525.00 while theirs is only 310.00 , thinking of giving them a try for 200.00 savings .

Does anyone have a good original lower sediment bowl nut/fitting ? The one on bottom that drain petcock screws into . Mine has a hairline crack & petcock won’t seal . Thanks in advance !

Hey everyone, I’ve been thinking of upgrading my rear gear ratio to be a little more highway friendly. Stock engine . Just curious if anyone had done this and what ratio you chose?

Hi everyone. Got a ammeter in the original ford box just curious if it’s a original or repop unit .

Parting out a 63 merc monterey 4 door , message me with your needs, thanks

in search of a running or close to it 28-31 tudor sedan. old paint a plus. stock drivetrain, no hot rod.

Hi guys, I located the lower door seals from berts but can find anything for top or sides of doors. What goes there & who carrys it. Thanks

Hi guys, did the ignition switch on a 29 have special nuts on it like the amp gauge had? Ordering some parts and found the amp gauge nuts but not the ones for switch. Thanks

Looking for a 28-29 pickup cab, may look at a 30-31 also, already have a chassis I'm restoring so need the cab only. Thanks

I was working on the speedo in my 29 getting everything free and cleaned up. The pin that holds the odometer shaft to the housing on the one end was beaded on both ends so I had to grind the end off then tap the pin out. Does anyone sell the pin or can a small screw be used in place? Thanks

Need a good used cluster gear for a regular a trans. Thanks

Hi guys, my 29 pu has been doing great. I let the truck set about a week and got back in it and I didn't want to start, the wire on starter was loose. I snugged that up and started down the road and it started smoking from behind the gauge panel. I pulled the panel off when I got stopped and...

I've been driving my 29 pickup daily now for the past week. I've adjusted the generator & it's putting out about 8-9 amps charge while going down the road at 45 or so. It has maybe a 1 amp charge at idle but when I turn my headlights on it drops down to a 10-11 amp discharge on low beams and...

Hi guys, I got to noticing tonight that my gas tank has a 4-2-29 date stamped in it and the frame number shows that engine was stamped the same day also. The chassis has the features that are listed in service bulletins from march 15 thru possibly the end of April( April 6th 29 shows the body...

I believe this is a 37-39 ford pass radiator. Has some bent fins but I don't see any busted flues. Tanks and sides are pretty nice. 150.00 plus the ride.