Search results

  1. J

    Welcome aboard

    Model A guy goes to get on a bus. He is carrying a drive shaft. Driver says you can't get on here company will not allow any package over four feet and that is five feet. Model A guy goes into a store and buys a four foot box puts the drive shaft in the box and waits for the next bus Next bus...
  2. J

    drive shaft and torque tube

    Drive shaft a torque tube Good used no rust $300
  3. J

    carburetor float valve

    Rebuilding a tillotson carburetor.Looking for recommendations on what type of float valve to use. maybe a viton plastic tip? Whats recommended and where can I get one? Thank you
  4. J

    1931 shutoff grommet install

    Any trick to installing the rubber grommet in the fire wall before installing the under hood shutoff valve.Its putting up a good fight and so far its winning.
  5. J

    Late 1931 indented firewall gas valve

    Looking for advice on my gas valve which has a slight leak when off. Brattons sells a replacement valve. They also sell a gas line which has a valve in the line, They have a fuel valve Stem which fits an original but how to tell an original from a repro...
  6. J

    Tow tooth steering adjustment

    Im working on adjusting my two tooth box.All is tight except when moving the pitman arm from front to back of car. I have about 1/8 inch play.This is in the box The bolt from pitman arm to shaft is tight I have about 4 inches play in the steering wheel.Would the 1/8 inch be enough to cause this...
  7. J

    1931 Gas valve removal

    Planning on removing the under hood gas valve on my 1931 and polish the seat to stop some seepage. Can I just unscrew it from the engine side or is it necessary for someone to hold it under the gas tank? i.e. a two man job.Thanks
  8. J

    Gas gauge Late 1931

    Gauge reads about 2/3 full when tank is full.There are no leaks at the gauge . Im thinking it might be better to try to bend the rod through the fill cap after removing the screen.Anyone have advice with this? Should I use wooden sticks so as not to cause a spark?
  9. J

    3.78 turtle

    Good used turtle $40 John Kuhnast 973 835 1472
  10. J

    Selling out parts

    30-31 Steering upper bushing New never used $6.00 Used original lower half of light switch body small amount of rust $5.00 Engine oil filler pipe and cap used good condition $10.00 John Kuhnast 973 835 1472
  11. J

    Selling out parts

    Good used U joint Tight and no rust $35.00 Rebuilt water pump $60.00 John Kuhnast 973-835-1472
  12. J

    Rear spring spreader

    Rear spring spreader Used once Excellent condition $50 John Kuhnast 973 835 1472
  13. J

    Selling out parts

    Original rear axle shafts May never have been used. Excellent condition. $230 each John Kuhnast 973 835 1472 Eastern standard time.
  14. J

    1931 Gas valve

    Have slight leaking gas valve. The under hood type, Can I polish this up with toothpaste while still in the car? Thanks
  15. J

    rear axles

    I have rear axles that have been in storage many years.They are in excellent condition and maybe have never been used. John Kuhnast 973 835 1472 $ 290 each.
  16. J

    First order

    July 15 1903 Ford Motor Co takes its first order. Chicago dentist Ernst Pfenning orders a $850 two cylinder Model A. Delivered just over a week later.
  17. J

    State inspection

    Im in New Jersey and not wanting to be bond by the restrictions of antique plates I registered my truck with regular plates. This meant having the truck state inspected every year including emissions. I just got a notice from the state that I no longer need to have it inspected.
  18. J

    U joint

    Nice no rust U joint Used but tight $50 John at 973 35 1472
  19. J

    Horn wires

    Repairing wire harness. What wire on the horn goes to the button and what goes to power? Thanks
  20. J

    upper pittsgrove new jersey

    When is the auction in Upper Pittsgrove New Jersey?
Back
Top