Search results

This is an intermittent condition. While running at speed the engine acquires a rapid ticking sound that I cannot isolate. Is it a worn timing gear and cam shaft action? It is not a wrist pin, ignition-timing or bearing knock type of noise. Thoughts? Is there a quick way to isolate a timing...

Fan pulley - upper pulley for two belts, one large V-belt, one smaller V-belt; for F100 272CI engine Gen Bracket - to mount generator on right side of 272 engine. This is for a 1955 272 Truck engine. Thanks, TQ

Seeking two parts for a 272 Y block for a 1954-5 Ford F100: PN 8592-cylinder head water inlet p. 249 in Ford Truck Parts, Illus. Sec 80 and PN 1342 Crankcase vent tube and related parts, p. 191 Ford Truck Parts Illus. Sec 66

I purchased a 1955 F100 3 speed transmission from a guy who tried to remove the rear output seal. Using the seal removal pry bar previous owner (PR) managed to mangle-out the elements of the seal - the rubber, a spring looking piece. The perimeter of the seal remains in place and will be hard...

Need a bell housing for my 1954 F100 PU and new 272 engine on a stock driveline, 3 speed transmission. Original 239CI bell housing not useable. I live in central Virginia.

This engine was pulled from a pickup in TN. I was told it was a good running engine at that time. It is the Ford OH 6 Cyl, with starter, carb and generator and appears like a complete engine. I was told it was a 1950-51 engine. Asking $450. Located in Eastern Virginia.

I purchased a 6 cyl overhead engine and was told i was a 1954 F100 pickup engine. I cannot determine if this is true. Markings on the engine are: NK72 F 5RR8 EAA - 615 - B Any assistance would be appreciated! Thanks in advance for the help! TQ

This road wheel is cast iron (some pitting). Cast letters Part 850, 35T8P, and JONES. 3 mounting screws and spacers included. Will entertain an offer. Also have an AC "Direct Drive" (left spindle) brass casting has embossed letters AC FLINT - in good condition. TQ

Need at least 2 (maybe 3) T 15x6". This is for a truck not a sedan which are 15x5.5 - slightly narrower. The stamped info on the rim says "DOT T* 15x6 JK1900 LBS MAX 41 PSI". Located in Central Virginia. * Indicating it is for a truck? TQ

Seeking serviceable rear spring shackles for the aft end of the spring. It is a Y shaped casting that allows the spring to flex. Mine are wallowed out from wear and poor servicing.

I have a few zig-zag springs in the bench seat cushion that are broken or missing. I have found furniture suppliers who have the zig-zag springs but not the long reinforcing stabilizing springs that are part of the system. Any suggestions for suppliers of such unusual items? An old seat...

On disassembly, noticed the rear left engine mount (bell housing) separated from the bell housing. Need replacement. Any possible suppliers out there? Believe it is 239 Y block engine.

I am restoring a '54 F100. Looked at door hinges and access to the pillar 6 bolts or the access door on the door itself (6 bolts). It seems that the door bolts make an easier removal. Any advice out there? Thanks.

I have a model t engine recently rebuilt, but when coupled to the transmission, it has a horrible vibration when shifting from low to high. It starts easily and idles well with a clear neutral. I would like an experienced mechanic to go over the engine and transmission to set it right. I...

I want to install a 6 cyl Ford engine in my 1954 F100 which came with a V8. Question: Will the V8 bell housing line up with the 1954 6 Cyl engine? Or, will need a 6 cyl bell housing and transmission also?

Seeking suggestions for material to use in the roof of the Victoria. I have insulated and sound deadened the entire body, but need to install some means of insulation or sound-deadener under the overhead fabric headliner. Bubble pack is unsatisfactory because it makes noise while traveling...

Seeking brackets for sun visor for 1931 Victoria. The brackets should be the same as used on slant windshield models. TQ