Search results

Wanting to buy - good used original or NOS center grill stainless steel trim for '36 Ford passenger car. Can't be repro. Thanks

I know this sounds odd but I want to buy a box full of air. Modern repro 1936 Ford V8 Passenger Car hood ornaments are usually shipped in a styrofoam container molded to protect the hood ornament (and especially the fragile "V8" stems) from breakage. I'd like to get one of these empty...

Looking to buy an original 36 hood ornament, can be in rough shape (broken V, pits are ok) but it cannot be a repro. thanks

Looking to buy one set of good original 36 front bumper brackets. Part number 68-17766 & 68-17767. Thanks

Looking to buy an original '36-37 dashboard light switch. 1935 appears similar but is not correct ('36-37 on/off is opposite of '35). thanks

Looking to buy an original correct lighter housing for '35-36 Ford, not repro. Thanks

Looking to buy a good original 35-36 striker plate for the rumble lid. Ford 48-713780-E should be iron, not interested in stainless repro. Thanks

1936 Cabriolet correct restoration. Tailpipe sticks waaay out and obviously needs to be shortened. Everything else in the exhaust system fits well (that took quite a bit of work). I searched and couldn't find this measurement. What's the correct length for the tailpipe, measured from the...

I need an original 1936 throttle linkage, must be 3-3/4" long as pictured. 1935 is shorter and won't fit. I don't know if 1937 etc. uses the same part. thanks, Ken

For correct restoration, looking to buy a late 1936 oil pan. If you have one to sell, let me know the details. Thanks, Ken

Looking to buy a good original 1935-36 male dovetail. Needs to be "centered" type similar to attached photo, not an "offset" dovetail. I don't want repro. thanks, Ken

Green arrows in the photos - three rubber round bumpers or grommets fit into the tin plate on the convertible top, inside the front edge facing down onto the windshield header. I have checked all the large parts houses (including Lebaron-Bonney) and have not found the correct round bumpers...

Looking to buy an original (not repro), centered (not offset) 48-702550-A male dove tail for 1936 passenger car. Same part fits all 35-40 closed cars & cabriolet. Must not be offset. These were manufactured 3 ways - offset-up, centered and offset-down. If you have one to sell, email a photo...

Searched and found other years but not 35-36. I'm looking for close-up photos of an original or correctly restored car where the A Pillar and B Pillar meets the sill. Trying to determine exactly how the windlace should line up and fit under the scuff plate. thanks, Ken

1936 Cabriolet - the attached factory photo shows the windshield header area, where I have a question regarding the grommet for the wiper motor vacuum tube. The photo I have is from a book, low quality scan - is a high resolution of this photo available? thanks, Ken

Assembling a 36 Cabriolet, need the seals between side windows and convertible top. I know 68-740928 and 68-740929 is the rubber seal between the front edge of each side window and the windshield header (fits into a stainless channel on the header). I don't understand if rubber seals...

Wanting to buy a B-11655-S "light switch can", installs near the steering box. Must be original used Ford, or NOS, not repro. I don't need the switch itself, just the lower half of the "tin can" as pictured. 1932 1933 1934 1935 1936 1937 1938 1939 thanks, Ken Fowles

Trying to figure out where this part goes. C&G and Dennis Carpenter list 40-7012130 as a Transmission Cover Seal for 1933-36 passenger car. This is separate from the Parking Brake Seal 48-700384. I haven't seen the location of this part mentioned in the V8 Club restoration book. The small slot...

Looking to buy a restorable original set of four hubcaps for '36 Ford in good repairable condition. Not interested in repro. thanks Ken

Looking to buy just the spare wheel mount portion to attach a 1935 wire wheel (5-1/2" bolt pattern) to side of a 1935 bed, not the wide-five wheels used in 1936-37. thanks Ken