Search results

I’m looking for a horn or a pair of horns for my ‘36 pickup. I’m not sure what is correct. I see some that have a curved bell (projector) and some that are straight. Are the car and pickup horns the same? Can you interchange the curved and straight bells? Any info on where to buy good used is...

I have a spare tire holder that bolts to the running board of my ‘36 half ton but it’s not made for the wide five bolt spacing. It came with my project. Did Ford make an adapter to fit this wheel? I plan to just make the triangular bracket because it can’t be seen with the tire installed, but I...

I need the two brackets that connect the windshield frame to the hinges. My research tells me that the car brackets are different from the pickup. Thanks. Tim timsmustang@gmail.com

Are there any manufacturer's that make these wheels? Looking for the 10-1/4 bolt spacing. If not, where is a good place to buy used? I need a pair.

I am working on the bed of my stock '36 pickup. I want to put in an aftermarket wood floor with metal strips in between. I have to replace all three sides as they are quite beat up and the original metal floor is rusted out, but the frame is good. I am trying to determine if I need to...

My project '36 pickup has the artillery wide 5 bolt pattern. I have some questions. Was this a stock wheel for 1936? Car or Truck? I'm measuring a 5 x 10" bolt pattern but read somewhere that it is actually 5 x 10 1/8"...which one is correct? I would like to put the '35 wire wheels on this...

Looking for the center upper cowl section or patch panel that would include the vent area for a '35 or '36 pickup or big truck. I believe they are the same. I have been told that perhaps the '37 and even later years might work but not sure. Previous owner welded the vent shut. I'm trying...

I have a bit of a mystery that I'm trying to figure out and was hoping someone here could steer me straight. I purchased a generator for my '36 and when I went to mount it, the pulley is about 3/8's of an inch too far to the rear. This is the pulley that a fan attaches to. I bought a...

I am looking for information on installing a cooling fan on a '35-'36 pickup. My project came with an electric fan and I would like to return it to stock or at least close to stock. I am using an alternator (12V) and while it is not stock, is there a way to adapt this to a fan? I am assuming...

I would like to put dual carbs on my project and am getting to the point of needing an intake manifold. I have not been able to determine if there is a vacuum port on the aftermarket units on the driver side that connects with the distributor. Does anyone here have a dual set up with the...

I am restoring a '36 truck. I recently pulled the engine and transmission to do some work on the frame. Decided to rebuild the transmission with help from Van Pelt's (actually spoke with Mac himself). The transmission rebuild went great. The pressure plate assy seemed perfectly good and the...

I am trying to locate a rebuild kit or at least bushings for the brake shaft on my '36 pickup (1/2 ton). I've checked several parts suppliers, but no deal. Anyone have a lead on where I can purchase this? Or do they not service this part? Mine is quite wobbly. By the way, this is not the...

Hello, I need an engine side picture of a 1936 pickup (1/2 ton) radiator. My understanding is that this is a one year only radiator. I have one but am not sure if it is correct. Thanks for any help...Tim

Last fall I purchased a 1936 Pickup. I do not know much about the history but the frame VIN checks out as a '36 and the transmission VIN matches the frame. A few days ago my son and I started tearing down the engine and I am confused. I'm hoping someone can tell me what it is that I have...

I am mocking up the parts on my pickup to check fitment. I am looking for help with a problem that I have assembling the front end of my project. I purchased used steel fenders and the pickup front fender front braces. When I installed the braces and the fenders, the grille would not fit...

Hello all...first post here. Purchased a 1936 half ton pickup for a father/son project. Today we decided to mock up all the pieces to determine what parts are needed. I have several questions that I hope someone here can answer. Like many projects, you can get a conglomeration of parts...