Search results

The 64 1/2 and early 65 Mustangs had carpet that only went to the bottom of the inner rocker panel. Later ones had the carpet extend up the inner rocker and under the aluminum sill plate. The early ones had a piece of vynil glued to the inner rocker pane. I have an early 65 with the 64 1/2...

Installing an original Shelby factory hood on my 65 Mustang. Got a repo of the hood rod prop. Been trying to figure out how to mount it to the car. Need details as to how it mounts to the car. Googled it several times and haven't found anything that shows how it mounts to the radiator support,

I'm getting ready to have the windshield put back in my Mustang and have about a half dozen somewhat large clips in a bag marked windshield and have no idea where they go. Have all the small clips that hold in the stainless trim in place. Can't see where they go. Possibley under the edge of the...

Painted gloss black, mate black, or natural?

Oil pressure gauge works fine. Gas gauge works. Gave up on amp guage. Temperature gauge is the problem. When engine starts to warm up guage goes all the way to hot. Stays all the way to cold until engine warms up. Tried different sending units and two gauges. Short the wire to the sending unit...

I haven't visited the site for a while. When you click on a thread it's unreadable. Funny odd shaped shaded areas all over it. What's with it? Lots of good info there if I could read it.

My new Early Bird Magazine had an article recomending replacing any tire after 6 years for fear they will fall apart. I put a new set of Black Diamond wide white radials on my T Bird when I put it back on the road several years ago. Won't have 5,000 miles on them in 6 years. Love them but they...

I'm clearing out stuff prior to moving next spring. Forgot I have about 30 of these and the projector. Mostly from the 1950's. Everything from new care intorductions to technical stuff like the Loadmatic distributor. Anyone ever seen these? Any Idea what they're worth or where to sell them...

I'm replacing the cork air cleaner to hood seal on my single 4 barrel air cleaner. The wire staples I got from Larrys T Bird parts are a little too narrow. to fit the holes in the aircleaner. If I bend them to fit the front holes they won't go through to the back set of holes. Haven't called...

Replaced regulator with new Americian made one last September and it died yesterday. This is about the 3rd one in as many years. Any suggestions for a good one or is there and electronic replacement available?

Does anyone know if the rear brake backing plates, drums, and brakes from a '70 Torino 8" rear end housing will fit on a '57 Ford station wagon rear end housing?

I talked to a few friend with Migs and figured out that mine has a non adjustable gas regulator and theres all have an adjustable regulator. Will and adjustable regulator be worth the cost?I have a Hobart 110 volt mig that I bought many years back. Never used enough to get good at it. Dug it out...

Working on putting together a hoist for the hardtop on my '57 T Bird. Bought a small electric hoist from Harbor Freight . Looking at geting. the part that holds the top from one of T Bird parts suppliers or making on myself. Suggestions from someone who has been there and done this? Found some...

The '65 has a running horse emblem on the drivers side of the gril. Looking for measurements to accurately locate it. Going with the Shelby look on my coupe. Have hood, side scoops and a lot of the engine parts.

Can I adapt the 65 wiring harness are do I have to use the whole 66 harness? Oil pressure gauge and amp guage should be the only difference. I would need the 66 oil pressure sender. Not sure about going from idiot light to gauge for the alternator.

I'm patching the lower rear section of a '65 Mustang front fender. Cut out a 6x6 section of rusted metal and made a patch to weld in. The inner support is rusty but solid. Plan is to clean it as well as possible and prime and seal it. Suggestions for products to prime and paint the inside...

I have a '65 Shelby intake on my Mustang that has no provision for mounting the kickdown linkage for the auto trans. Been running it wihtout the kickdown strictly for an occasional mile or two run to keep everything working. Mechanic friend says runing it without the kickdown will trash the...

The one that looks like a truck or tractor knob. Reverse is to the left and up.

Fits large input toploader out of 428 or 429 Cobra Jet. $100 plus shipping. Call 618-530-7021