Search results

I got a new bulb and i may have thrown out the housing. Still looking but unsuccessfully. Will add a pic or two. Hoping someone has one. I dont need the bulb, just the little housing and funky clips that hold in the bulb. Bought from joes antique auto parts in mass. I found out it is made...

Hello all, Long time. My car is all set thanks to many of you helping me out with all kinds of issues. I am currently helping my 79 tear old dad work on a 36 that he wants to put a 37 steering box in. We installed the box, lined up the bottom hole, slotted the middle hole slightly, and welded...

need one s.s. bezel with good spring clip. "accident" but will take (2) to match a driver. may take whole bucket too...but i think my bucket is not damaged too much. thanks, send pic to chip8@msn.com thanks, cp

We bought another 6v coil and all was fine and installed with the "+" to the distributor since truck is 6v "-" ground. Truck solenoid started clicking recently. I have been unable to find a wiring diagram for a 1939 pu. Van pelts does not show. All part suppliers show the solenoid as a...

Tried to search to no success. Replacing an original 6v positive ground coil with a new 6v coil. Old coil is for dummies like me. One terminal says battery and the other says distributor. The new coil says "+" and "-". I thought the "+" would go to the battery even though + is ground. It...

Looking for original 36 fuel sender. Thank you

1936 FUEL/OIL GAUGE w/ OR w/o SENDER

Hello all once again, just realized there is an original resistor under the dash that I never knew was there. From other posts....i found this "14.2V / 3.5 Ohms = 4 Amps" I'm running 12volts 1948 flathead with a Mallory electronic distributor. Mallory paperwork requires ballast...

Dad needs his generator repaired. Thinks there is a guy in Wilmington Mass but lost phone number...Any leads appreciated. Thanks CP

need a condenser for 46 to 48 crab. dual points. running 12v if that matters. would like 2 so I have a spare. will read up on the 'e"-men posted by bubba about 5 years ago. thanks, cp

read here often and have not posted in quite some time. all has been going well. However, the last time I made the trip (300 mi ea way) to Vermont, she started running like crap the last 50 miles or so. Luckily I made it home ok. I have yet to change the cap, rotor, plugs...

Hello all, I have not posted in quite some time. Still read forum often just haven't had the need to ask any questions since I asked many a few years ago and have learned a lot from all of your help. Evidently (no surprise) I have much more to learn. Here's the story.... My nephew...

i have the horizontal part that the license plate bolts to on the bottom. i just need the vertical. thanks cp

I do not remember my starter looking like this. Before i spend the time clearing out the garage to replace my starter. I was hoping someone could tell me if this starter looks right. My brother got it for me. Guy told him it was a ford starter and would fit. I'm thinking not.

I just noticed that i am a "senior member". ....... No Way. No How. I'm not old enough..not smart enough, and not respected enough. In other words... I respect all you smart, old guys. Thanks for all you've done for me. I would still be driving a pontiac if not for the Fordbarn...

would need photos and maybe a couple dimensions to make sure they match the ones i have. mine need rebuilt. thanks charles.

i have been in the hunt for the valve tools needed to tear apart and old engine. i was looking at the Van Pelts pictures of coarse and paying top dallar for two out of the three tool he lists on his web page. i was thinking....finally... there are alot more tools than just the ones "he"...

i recently "luckily" found a kd-918 im looking for a kd-917 and the long bar with the fork on it. of course after i get the tools, i'll also nee some direction on how to use them. ill be honest. ive read and read and read, but i need someone to just tell me how to remove valves from a...

thank you, charles