Recent content by tsteger

I have a pair fenders for 67 and a pair 68 $300 pair=== doors for 67 gt not perfect but better than normal $400 pair--- 67 roof---68 formal roof trunk lid--- 67 trunklid $ 200 each----torque boxes for Fairlane 67-69 $350 pair $200 pair---rear 3 foot frame rails 67-69----67 gt convert left...

anyone have a pair of rust free or NOS fenders and radiator support for a 59-60 half ton pickup truck thanks one,seven,one,seven,six,eight,eight,five,six,seven,four

I have parts listed on York pa and Fredrick md craigslist under fairlane . I have a to much to list . have a look and see if you can use any of it, some is going to scrap yard to make room in the garage if it does not go in a timely matter. tired of advertising them, thanks tim

looking for a nice gas tank for a 59 f-100 pickup, may be same from bigger truck. would like a clean rust free one that fits in the original location behind the seat, one, seven ,one, seven ,six, eight, ate, five, six, seven ,four thanks tim

I am still in need of window roller bracket that pushes on the springs to hold roller into window frame, I believe this is 39-40 convertible only. also need a good pair of front shocks for the 39 and the 2 short pieces of chrome strips for the grill, they at 3 to 4 inches long , guessing! and...

anyone have any measurements for the 2 steps on the right hand fender. I need to drill them in my fender to be able to get in the rumble seat, also I see the convertible top guys list 2 different header bows above the windshield. what is the difference other than one is tapered on the end and...

I have a 39 convertible coupe. I am working on the header bow. I have a 40 year old reproduction wood bow . it will not fit the contour of the windshield frame and the pre drilled holes do not line up. the weather strip gulley machined in it for the rubber seal to fit in is not on the right...

I have a 46 flat head engine from my 39 , loose but needs rebuilt mostly complete. I have a 39 deluxe car hood and 2- 40 standard car hoods , 1- rear fender for 39i believe right hand needs work, new lh floor board and and a rubber kit, a new glove box liner , best reasonable offer on all or...

I am in need of the bracket that pushes on the springs for the window rollers of a 39 convertible coupe with rumble . my car is missing one , I have 3 and need 4 thank you, tim , 17176335059 leave message or email me at [gtstripecar@aol.com]

doors l+r 63 hardtop galaxie $300,,,doors l+r 63 sedan galaxie $300,,,doors l+r 64 hardtop galaxie $300,,, doors 2 rh 67 fairlane$100 each,,,dash pad 67 fairlane $300 one crack,,,68 torino quarters cut from car belt line down use as patches or whole $300 pair,,, full quarter and fender 67...

wanting to restore or paint old fords . we do metal work, [quarters replaced, floors , ect.] we like and know 62-64 galaxies in and out especially big motor cars, also have parts for too. will work on any old fords though and other brands to fill in. 30 plus years in business , we are very...

wanted an NOS right hand quarter panel for my 68 fastback torino, also a second gear servo for a c6 with an R on the cover please contact at [gtstripecar@aol.com]

i have 2 dash pads $500.00 each not perfect but close as they get , fenders and doors $300.00 each , floor shifter for an automatic with hump $250.00 for all parts to it , pair bucket seats-need recovered $400.00 each one set each for 67 and 68 fairlanes, 2 big spline 4 speeds for 69 and 70...

looking for an NOS right hand quarter panel and a 2nd gear sero with an R on it and a floor shift locater arm for a C 6 automatic trans for a 68-69 torino-fairlane fastback. email me at [gtstripecar@aol.com]

need the accelerater mechanizm that attaches to the gas pedal and bolts to the firewall and hooks to the carb linkage. must be for a V8---- call and leave message 717-451-4511 thank-you