Recent content by 61 BLACKTBIRD

1 1952 Ford Shop Manual, $30.00 Plus shipping. Please contact me off line, ( jfboyd1942@cox.net). Thanks Jerry

I have a lot of baby bird items for sale; Book collection, cars, puzzles, games, Beam bottle (gray), I have sold all of my Thunderbirds and am unloading my collection. Please contact me off line ( jfboyd1942@cox.net ). I also have several other Ford items. Thanks Jerry

Two AC Fuel Filter Systems. They are both the short glass bowl and have the filters. One has the large A C on the top on the assembly and the other has the smaller A C in the circle. both boxes show TYPE GF-48 gas filter. The price is $ 40.00 for each filter. jfboyd1942@cox.net 479-651-3773

One set of 1956 THUNDERBIRD exaust deflectors. These are new old stock with a few small spots of surface rust from shelf life, no dents or dings. All that is needed is a light sanding and some paint. jfboyd942@cox.net 479-651=3773

Does any one have a picture or diagram of the 61 T-bird Skirts. I am trying to figure out the pins that came with the rubber seals. I cannot find any holes for the pins. Do not have another 61 t-bird in the area to look at. Thanks, Jerry:confused:

One original set of 2nd generation headlight lens. This is a matching set that came off the same car. Both lens has the Ford oval at the bottom with an H right below the Ford. Both lens has the following numbers at the bottom ( A-13060 M C K ). The one lens has a smaller C than the other. One...

CAUTION for everyone using duct tape as a wheel liner The first wheel I did was a reconditioned wheel I had restored. the next two I took off the car were banded with duct tape. One wheel had a small amount of duct tape that had been moved by the tube and kind of wadded into a little ball. Where...

I am going to install an A/C unit in my 1961 T/bird. There are several different units, but I keep coming back to the CLASSIC AIR unit. Has I LIKE THE TWO SEPERATE HEAT & AIR UNITS ON THIS SETUP.anyone had any expearience installing one of these. I would like to know the pro's and con's. I do...

A followup to my above message. Yes, I preped each rim by sanding roughspots, painting, powdering the tire and tube. After installation of the Truck Tire Bands I did a small amount of trimming on the band to keep it from curling up on the side to interfere with the tire. I do have two rolls of...

I went to a Truck stop and got an old 36 inch diameter inner tube. I then cut 61/2 inch wide bands for the inner liners. Once I stretched them over the rims they worked great. This is how I took care of my problem. No taping and yes I used the Talcum powder like it was snowing. Thanks for...

I would like to talk to someone that has used the black puumbers tape to cover the spoke nubs on the inside of the wire wheel. This allows the use of tubes with the radial tires. Each rim has the sprayed on black material covering the spoke nubs. Where do I go from here ? Thanks to All:confused:

I am looking for an Inner fender panel. This panel fits on the rear of the Left Front Fender and covers the brake and fuel lines coming into the engine compartment. Any help would be appreciated

Please send me your e-mail address and I will furnish pictures. I just joined and do not have this site figured out yet. The trailer hitch is very nice. Jerry

I think I have what you are looking for. I have a 29 Open Cab Pickup that I was going to put a bumper on and then changed my mind. The brackets even have the 6 inch piece welded into them. Please send me you e-mail address and I will send you pictures. Thanks

I have a trailer hitch and a ball that is rated at 3000lb. The hitch came off a 1931 Roadster. I would be willing to sell it for $ 150.00 plus shipping. Let me know