Copper B Head Gasket

Dick Deegan

Dick Deegan

Well-known member
I am just finishing up my engine after a extensive refresh and am about to install a copper B head gasket on an A engine with a 5.5 head.

Which side of the gasket faces the head, or does it matter?

Thanks

Dick
 
on a copper gasket, or any gasket one side will be smooth, the other side around the cylinder bores will be a crimp that crimp goes against the head,the idea being that an engine viberation is delevoped by the pistons firing and may cause wear at the crimps, its easier to surface the head than the block to remove the wear
 
I don't really know. I bought it from Mac's a couple of years ago. Hope that it works!! I did spray is with copper spray on both sides prior to installing. It looks like the one in your picture.

Dick
 
The head gasket Snyder's recommends for the 5.5:1 head is not a copper head gasket, it is head gasket Snyder's sells that is coated with silicone ; additional high temp silicone bands surround all water passages. Install with no additional sealants.
Snyder's listing: B-6051-M (for 1932-34 and Snyder's 5.1 or 6.1 Head).

Ron
 
Last edited:
Thanks Ron. Yes, I am aware of this and have used the silicone coated gasket in the past. I did contact Snyder's at the time that I bought this gasket and they stated that as long as it was a B gasket it should work. We'll see!! The only reason that i am using this gasket instead of the silicone gasket is because I have it in stock. Trying to save a few dollars.

Dick
 
I may be a bit late on this one but I always use a copper asbestos head gasket, the reason is you can always use it a second time in an emergency
Ahooga
 
Tanglfoot said:
I may be a bit late on this one but I always use a copper asbestos head gasket, the reason is you can always use it a second time in an emergency
Ahooga
Click to expand...
Tanglefoot,
I can just "see" Chief shakin' his head, no, no, that'll just cause ANOTHER emergency about 17 miles down the road!! Bill W.
 

Attachments

  • Stuck_in_Mud,_Pie_Town,_N_M_,_1940.JPG
    Stuck_in_Mud,_Pie_Town,_N_M_,_1940.JPG
    59.8 KB · Views: 71
BILL WILLIAMSON said:
Tanglefoot,
I can just "see" Chief shakin' his head, no, no, that'll just cause ANOTHER emergency about 17 miles down the road!! Bill W.
Click to expand...

Bill
18 miles in NZ and I would be home with most of the water intact
What I meant was the other sticky type gaskets have to be scraped off so you have nothing left
Ahooga
 
Tanglfoot said:
Bill
18 miles in NZ and I would be home with most of the water intact
What I meant was the other sticky type gaskets have to be scraped off so you have nothing left
Ahooga
Click to expand...
Brother Tanglefoot, I knew what you meant, just havin' a little fun! We could be brothers, with my braces, I often tangle my feet & CRASH!
Chief knew an old man who took 2 used head gaskets, layered them with # 2 Permatex, and ran his '29 Chevrolet for years!! Bill W.
 
Bill: I'm with Chief and his friend. Plastic, silicone, epoxy, whatever, #2 Permatex is all a mechanic needs. Carry it in your tool kit. (#3 is convenient on occasion.)
 
PC/SR said:
Bill: I'm with Chief and his friend. Plastic, silicone, epoxy, whatever, #2 Permatex is all a mechanic needs. Carry it in your tool kit. (#3 is convenient on occasion.)
Click to expand...
PC, Dog:cool: here, what is that # 3 crap?:confused: Maybe that's what I got stuck on my R/F pad,:eek: DANG stuff won't wear off!!:mad: Goes, TICKY TACK, TICKY TACK, when I go across the hard Pergo kitchen floor, Bill LAUGHS!!:D Well, he DIDN'T laugh once, when he fell on the same HARD floor and drove his SCHNOZZOLA clean into his face, so, he who laughs longest---------------------------Buster T.:cool:
 
You must log in or register to reply here.
Back
Top