292 312 Ford Engine

ncauclair said:
I took a photo of the number on the block below the distributor. ... I tried to post the engine photos here but it won't let me????
Click to expand...
The "file size" of the photo has to be less than 2mb, to be able to upload it.

.
 
Last edited:
There is a letter/number cast into the side of the block above the oil pan rail. If you see ECZ-xxxx-A or C, there is a good chance it is a 312. The only way for sure is to look on the crank flange for a flat spot with a dot in the center. Then it is a 312. Ford made both 292's and 312's on that same block in the last years of the 312, just machined the main bores to a larger size for 312's. John Mummerts website shows and explains all this in greater detail.
 
streetdreams said:
... The only way for sure is to look on the crank flange for a flat spot with a dot in the center. Then it is a 312. Ford made both 292's and 312's on that same block in the last years of the 312, just machined the main bores to a larger size for 312's. John Mummerts website shows and explains all this in greater detail.
Click to expand...
The dot on a 312 crankshaft, as streetdreams mentioned. (photo 1)
Main bearing caps for a 312 have an ECZ prefix casting number. All others are EBU.

Two links to the *ID a 312* pages on John Mummerts website...
http://ford-y-block.com/identify312.htm
http://ford-y-block.com/crankshaftid.htm
 

Attachments

  • crank dot 312, arrow.jpg
    crank dot 312, arrow.jpg
    38.2 KB · Views: 9
  • ECZ main caps c.jpg
    ECZ main caps c.jpg
    78.8 KB · Views: 10
Last edited:
I've been trying to post a photo of the engine. But it says my security token is missing? Dumb guy--don't know what that means. The photo isn't large MB?
 
If you can send the photo to dmsfrr@gmail.com I'll try to post it for you.
But it may a bit... I'm fairly busy today cleaning out a space in the garage for a car I'm leaving town to pick up tomorrow.
 
here are the pics.They were between 4.5 and 8.5 MB
 

Attachments

  • yblk1.jpg
    yblk1.jpg
    27.3 KB · Views: 37
  • yblk2.jpg
    yblk2.jpg
    56.8 KB · Views: 36
  • yblk3.jpg
    yblk3.jpg
    96.4 KB · Views: 34
Still cannot determine engine size. The cross over exhaust is early, but I've seen 312 long blocks under that old exhaust and lifter galley covers.
 
thanks for posting the photos-you're more computer savvy than I. I'm listing the engine for sale. What's a fair price? Part it out or as a whole? I live in Greenville VA. I have a couple of Ford trucks a 62 and 64 F 100s. Picked this engine up to put into the 62-- but we ended up rebuilding the one was that in it.
 
I'm listing the engine for sale. What's a fair price? Part it out or as a whole?
Click to expand...


That's going to be hard to determine until the engine is identified.

Where is Greenville, VA?
 
I can take a guess from the pictures, but a block and head casting number would help a lot. Heads are '56 or later. The distributor is '57 or later. Rocker arm adjusting nuts are '57 or later. The front cover has two flat machined bosses on top (I think that's truck ?).
If I guessed, I would say it's a truck 292 from '58 to the early 60's. Plus pretty sure they stopped building 272's after 1957.


Sal
 
the 272 was used in early 58 and then was upped to 292.scicala pointed out why it should be a 292.the valley cover is 58 or newer.unless someone shifted things around its a 292.if we knew what heads we could figure the year.
 
Let's guess the ENGINE ID with just a few picture ...

That engine could be any combination of parts over the service life of the FYB.

It has to be ID'd by the CASTING ID and DATE CODE NOS.

What if the OP tries to sell it using incorrect info and once the buyer puts it on a forensic table finds what it was described as isn't?

I feel like I am watching old I CAME NAME THAT TUNE TV shows ... :rolleyes:
 
You must log in or register to reply here.
Back
Top