Search results

Nice 50 Merc coupe restored from the ground up 2000 miles ago. Did not chop but shaved trunk and hood and added bucket seats and a console. Exterior is Dark blue and custom interior is blue/gray. Was a California car so I sandblasted it inside and out and replaced all glass, wiring and rubber as...

NOS Model A Ford muffler. Never been on a car. Must sell moving. Was a spare but sold my Model A. Will not ship. Only selling this cheap because of the move. Compare prices in the catalogs.

I have an original 1937 60 hp Ford Reference Book in excellent condition. This was the book that came with the new car in the glovebox. Shows some minor use but no tears or folds. Asking $30.00.

Gas is fresh !

Tank is stainless. Haven't looked in carbs but did spray starter fluid and it still didn't fire. I'm wondering if my coil has gone bad. I get fire but I'm wondering if it is hot enough.

Help, it acts like it wants to start but stumbles. It has 2 Holley 94s, the dual point Mallory dist. was set by Bubba and I set the timing. Also checked each spark plug and am getting fire on all of them. Suggestions would be appreciated. Only 5000 miles on a rebuild but haven't been run in 2 yrs.

Straight 1937 Ford firewall from a Tudor. One small rust area in battery area. I removed it by cutting the spot welds with a spot weld drill. Reinstall by welding up the holes in place. Will not ship !

This engine block is just back from the machine shop and has all components their for you to assemble and know it was done right. It is bored .040 over, new Pistons & rings, crank and cam have been dusted, new inserts for rods & bearings, valve seats machined as well as valves, adjustable...

I have a new old stock original type muffler for a Model A Ford for sale. I purchased it some 30 yrs ago as a spare and never used it. It has never been on a car. I sold my Model A recently and no longer need it. Must pick up at my garage. Will not ship.

Sold

Nice Tillotson carb. That I have had for 20 yrs. or so as a spare and have sold my Model A. It is in excellent used shape. Have many more engine spare parts to sell. If interested call me. 765-729-4777.

Model A Ford starter painted and ready to install. Have had it 20 yrs. or so as a spare and sold my Model A and am getting rid of spare parts. Have many more engine parts. Call me 765-729-4777.

Nice Model A Ford head for sale. Have had it 20 yrs. or so as a spare and sold my Model A and am getting rid of spares. Have several other spare engine parts for sale. Call 765-729-4777 if interested.

Nice Model B head cleaned, painted and ready to install. Was going to put it on my 29 Tudor but sold the car last week. Asking $110.00 plus shipping if you can't stop by and pick it up. Have several other engine parts for sale that were my spares. Call me at 765-729-4777 if you want it.

37 Ford rearend assembly drum to drum and torque tube and rear spring. Drove the car before I removed it and set it outside 10 yrs ago. Have not been inside to know the gear condition but still many good parts. Must pick up at my garage in Muncie, Indiana before Sept. 6.

Anyone have a 49 or 50 Merc ****** that maybe the gears were trashed? I'm in need of struts, shift sleeve and the needle bearing that is in the input. I bought a basket ****** years ago for a spare and started to finally assemble it yesterday and found parts missing. I may even need more parts...

I have a Jan 1930 engine (A2821408) that was professionally rebuilt by Ron's Machine Shop in Shandon, Oh in 1998. It has been inside all this time and never fired. On his web site he lists this engine at $2725.00 today. Not sure of wait time. I am asking $2500.00 for this engine with the head...

I bought adjustable lifters and new springs when I rebuilt it 3000 miles ago. New development: just pulled the cam and all 16 lifters and the lifter on the exhaust valve on the 2nd cyl. On the drivers side has a divot worn in the cam surface on the lifter perhaps .030 deep and slightly off...

Update: pulled intake, heads and timing gear and all 16 valve assemblies. No problem found. Does seem to be a lot of clearance between the end of the cam and the cover. Should there be a spring in the cover to keep some tension on the end of the cam? Now I'm wondering if I've gotten a chip in my...

Sounds like you may have failed to retorque the heads after running for a while. I always retorque twice. A buddy of mine had a Model A engine professionally rebuilt, brought it home and never started it for 5 yrs. He installed it in the car and we put water in and fired it up and it sprayed...