Search results

Ok guys, thanks for all the help on here. I'm going to do the rebuild and just call this topic closed. Thanks everyone.

I hate these vacuum controlled heater units. In my galaxie I ended up just using bailing wire to temporarily wire everything in defrost mode and dash heat only. At least it makes it drivable. In a bind you could probably do the same for now. I was a farm boy and we learned to work with what we...

Would putting oil restrictors, aka Holley jets, in the oil feed tubes help increase pressure enough to get by until march? If so would motorcraft jets work in place of Holley jets? I have plenty of them

Ok guys, I know it needs rebuilt. I just can't afford to until March. I'm trying to keep it running until then. I have been fighting a never ending battle and only can afford bandaids until march... Thanks for all the help guys

Im convinced I need to pull the valve covers off and make sure I tightened everything down properly and have everything put in there correctly. I will update everyone on my finding later tonight. thanks for the help guys. Switching from 20w50 to straight 30 made my oil pressure worse actually...

Its definately a mechanical tick. I am certain of that. wouldn't a straight 30 weight oil be thinner than a 20w 50 at full operating temperature? I though that the oil thickened to 50 when hot? I have considered doing a straight 3 in the past and just assumed 20w 50 was better. If I give that a...

The sound is very much like a small metal hammer tapping on metal. Definitely not an exhaust leak as it only does it when the oil has reached full operating temp. I really think it has to do with low oil pressure ar idle because it's the only time that the sound occurs. I don't think enough...

vacuum holds a steady 19 psi. Lifter was worn. My oil pressure is pretty low at idle too so I wondered if it was an oil pressure issue? at 650 rpm its at about 8 psi. cruising at 2,000 rpm it holds about 30 psi. anything sound alarming or possibly the cause of the tick? rhanks guys. Good memory...

Thanks for the replies. First thing to eliminate is the ac compressor. I removed it haha. Second is that the rockers are the non adjustable rail rockers. When I pulled them I did notice that one of them was worn alone the surface that presses the spring. The lifter on that one was also pretty...

What would cause a tick that goes tick tick tick TICK TICK TICK tick tick tick, silent silent silent silent silents, tick tick tick TICK TICK TICK tick tick tick, silent silent silent silent and repeat to infinity and beyond. It only happens when the engine oil reaches full temp. The sound seems...

Oh dang your right... I drove a whole day with the gas in the trunk not realizing that it had spilled. Luckily my kids were not with me. Since posting this I have removed the gas cans from the trunk. thanks for the heads up guys. I wasn't thinking.

HAAAAAAAAAAA! Thanks so much for that link. Thought I was s**t out of luck with the gas tank. It even has the seal. Thank you thank you thank you.

Here is a good chart I found on google for rich/lean spark plug reading.

I wonder if the heat riser going from the exhaust manifolds to the element is helping as well? I put it back on yesterday and it drove better in every situation, hot and cold. So the obvious thing to do is leave it on! Its my daily driver right now so performance is more important than shiny stuff.

Could the brake lights cause a spark if there was a spill again? That was the first thing that came to mind when I found the pool back there. Second was, "well at least I know my trunk doesn't leak."

That already happened to me... I had a gas can in the trunk as a reserve since the gas tank is only a 6 gallon. Well apparently I took a corner too fast at some point because I went in the trunk and it had tipped over and I lost about 4 gallons of fuel and it was a pool back there! Now I strap...

Dropped the gas tank and it was so full of rust tbat when I turned it over, rust poured out like gravel. probably a gallons worth of rust in the tank and when I strapped it to tbe end of a cement mixer and spun it with chains in it, the tank looked like swiss cheese. I decided to put one of thos...

makes sense. thanks

I guess what I am really trying to figure out is "WHY" it runs better with the stock air cleaner. Only thing I can think of is that the stock air cleaner is more restrictive and that the engine is running lean? I ordered bigger jets to see if it helps. going fron 54s to 60s. I know its a big...

do you need a drill press or could I just put it in a vice and hand drill it? how critical is it that the holes are perfectly vertical?