Search results

  1. O

    37 starting question

    thanks again, ernie
  2. O

    37 starting question

    more info. no glass bowl on the pump, stromberg 97 carb, rebuilt by Charlie, Iput a new pump on fromD ennis Carpenter, new in the box but 20 yrs old. coil by Skip, condenser and points new. I did not have the fuel pump rebuilt that was on the car when this issue came up. maybe neither pump is...
  3. O

    37 starting question

    I have a 37 that starts right up when its cold. after i've run it for awhile , I will turn it off, and 20 min or so later it will not start. If I pump the accelerator pedal 5-6 i t may start reluctently. carb recent rebuild by Charlie NY. I put a new fuel pump on with similar results. doesn't...
  4. O

    37 transmission question

    Zeke, thanks for the response. I did not want to remove the rear ****** support ,if I dint have to. your advise is right on. A lot of work to pull a ******! thanks , Ernie
  5. O

    37 transmission question

    I'm almost ready to remove the transmission from my 37 club cab. does it go down and out or up and out? it looks tight either way. And i would like not to remove the rear mount if that's at all possible. any thoughts are appreciated. Thanks, Ernie
  6. O

    33/34 commercial Dash lite and switch

    I have a lamp switch by vintique #40-13740. never opened. 3155324567 Ernie
  7. O

    34 pickup grill lacing

    the lacing on my 34 BB has a metal tab on either end that fits into a slot by the radiator cap and another one down by the fender. these get bent over to keep it in place.
  8. O

    lug nut torque

    Happy Easter. I have a 1934 BB truck with dual wheels. I wonder what the correct torque is. Ive seen anywhere from 50 to 100lbs. Thanks
  9. O

    Bb truck

    thanks for the info. im going to look for the Ford Shop Manuel
  10. O

    Bb truck

    Hello all. I’ve asked several questions about redoing the brakes on my 34 bb truck. I’ve had good info from the barn. It’s going back together and I’d like to know how how much pressure to seat the inner bearing and then how far to back it off and how much pressure to seat the outer bearing...
  11. O

    2 ton truck question

    Thanks again, all good information. Is there a book/reference for more info on the early Ford trucks?
  12. O

    2 ton truck question

    Thanks for the detailed answer. I have 6.50 duals a heavier frame and helper springs. More like a 2 ton than 1.5
  13. O

    2 ton truck question

    I have a simple question . Did Ford make a 2 ton BB truck in 1934?
  14. O

    BB truck question

    Thanks guys for all the help
  15. O

    BB truck question

    Thanks, there was no seal on this side. Now the snap ring makes sense.
  16. O

    BB truck question

    Re: 34 BB truck question Thanks, I’ll start there.
  17. O

    BB truck question

    I got great advice on how to remove the rear brake drum on my 34BB. I’ve discovered a broken snap ring. Does anyone know where I might locate parts? It’s a full floating axle and the snap ring is 3.24 inches in diameter. Also does anyone the purpose of it? Thanks
  18. O

    34 BB truck question

    thanks, I have no hub cap, but it would be about 6". so i must have the later model axle.
  19. O

    34 BB truck question

    thanks, seems like there is some variations of the 34 model
  20. O

    34 BB truck question

    I'm in the process of inspecting the rear brakes on my 1934 BB truck. I have a Ford service book with minimal info. Is there someplace where I might find more detailed info? I've got the axle out and could use a little guidance. Thanks
Back
Top