Search results

RE Penny block off . You have to use old penny the new penny is not penny is made cheaper and not as good, [ like a lot of new parts} l l Lee34

The cowl (dents) are much more noticeable than I see in your pics 33 Ford had flared place on the radiator.In the same area the 33 did not have a screen in the cowl vent.The screen was approved for production the last week of Feb.All together there were over 60 changes from the 33.The serial...

There are some vehicles that have independent rear suspension that use 2 u joints for each axle plus u joints on the drive shaft.(Total of 6) Each u joint can be installed 180 degrees off. when installed out of phaze operation is greatly affected more so at slower speeds I think most drive...

L78 There is a very good place in Louisville.They shaved my tires on the car..My wheel was a spoke wheel .They also balance your tire on the car (do not remove hub cap or any thing)They balance and check high speed operation as well.They are located on Poplar Level RD. The business name is...

The 2 inner holes on 33 are 22 in apart and 34 are 26 in apart .They can be used on both years if same year brackets and bumpers are used together (not correct for year for restoration) Lee34

The reflectors that Drakes sell (possible others) are different than original.The problem seams to be worse with the h4 type bulbs.They are bright enough just not focused.I purchased the kit from Drakes and only changed the reflector,I did not change bulbs so I could see if the reflector was the...

I had a 34 sedan with original lense and h4 bulb with same symptoms,I purchased Drakes reflector kit and now I can see I no longer have to use Braille to drive at night Try to explain to your wife your reflectors are worn out and you are spending over $100 to get new ones.(but worth it) Lee34

Jim;You can get one from RON FRANCIS WIRING 800-292-1940 www.ronfrancis.com Simple hook up.2 wires.Does not even need to be grounded.A little on the loud side.I am sure there are others out there but this works for me.Good luck lee34

Owned this car for 52 years...Think I'll keep it...only owe one more payment..LOL! Lee34

Have you checked to see if the running lights and brake lights are switched so the proper element is not receiving voltage as needed ? lee34

The original 33 & 34 bumpers had a ( 0 ) stamped on the back side. sometimes only a partial of the 0 made contact leaving a ( c ) . Both of mine are stamped on the left side (while looking at installed bumpers) lee34

Your trunk may be a trunk that was made to go on top of a luggage rack.There was several different manufactures for the trunks.In 1934 the Potter trunk was was the only one authorized by Ford.Later models of Ford had the trunks built on as part of the body .(Hump back).I think Potter went...

The 34 has a notch on top of the cowl for the hood to be held when open and 33 do not,34 has a screen in the vent and the 33 does not.If the dash is still attached all the gauge are mounted to a panel and that panel is mounted to the dash only on the 33,The 34 have a hole in the side where...

fREDERICK Checking a cylinder by pulling a plug wire off can cause damage to electronic ignition components .You can use a plug wire that is pulled off and attach it to a plug touching the motor no problem.A plug wire pulled off and not touching a ground (motor or frame) can cause the coil...

Like alchemy stated they all seam to be different Look at the tie bar at the bottom ,most are not uniform lee34

Could this be Fords answer to Chevy wing ? Lee34

Notice how every thing on e bay fits 34 Ford (0r it says so) Lee34

I have vintiques dual pattern for 10 years.Mine are tubeless and they are spoke type.Had some trouble with leaks at the rim spoke area sealing.Found the cause was porosity in the sealer to seal the spokes at the rim.I found the porosity with soap bubbles.Using a course burr i opened up the area...

On the extra tight bushing tap threads in the bushing take a bolt with the first part of the threads removed,screw the bolt in and push the bushing out.Try the grease method first.lee34

Shadetree;How about curb feelers,port-a-walls,49 Plymouth bumpers,drag pipes made from gas tank filler necks (just twist off the cap and you bypassed the smittys),chrome covers for your motor parts(generator,regulator,head bolts,coils).Flipper hubcaps and lets not forget gasoline 30 cents a...