Search results

It it possible that the ammeter experienced a surge and has now stuck in the far left by riding onto a pinstop or other obstruction?

I will recommend that all original ammeters should be serviced prior to use. The original design is not intended to last 80+ years. They can get very hot due to resistance in the bridging or the formed fiber frame can warp to create a dead short. Be careful.

Your original temperature gauge is a King Seeley thermal type to be used with a King Seeley points regulated sender. The gauge should start on HOT and travel to COLD when the key is energized. As the coolant temperature sender heats up, the internal points make contact less frequently thus...

The faces are frosted silver plate, then printed, then clear coated. The yellowing that occurs is due to the clear coat aging.

By 47' I believe you should have the black background. In general, one should be skeptical of eBay listings, etc. Do you not have the original gauges for confirmation?

You are 100% correct.

Be gentle with the trip reset stem. Often, we see damaged gearing on the trip meter side from abuse. Also if you have the Deluxe model with the quick reset trip odometer, take extra care. They are not a serviceable item.

On the sending unit: they are not a rheostatic type sender as you find in applications post-1956. King Seeley used a points style sender which you can research to infinity on this forum. Testing would require you to have NOS components to compare. It also helps to have a "feel" for the pulse...

The original fuel sending unit top looks like a "flying saucer" with a 6 screw mount flange. Double check the continuity of the wire to the gauge while you have access. As for the speedometer, check the cable, but also check that the magnet shaft of the speedometer is free. Often, the...

Are you using the original King Seeley gauge and sending unit?

The original King Seeley fuel level sending units can be repaired, usually. I have had many customers tell me that the aftermarket units are unreliable.

On gauges, you can use a solid state or the points style voltage regulator, but it depends on what sending units you are running. Are you using the original senders or? www.morrisgauge.com

In theory, your mechanical temperature gauge adapter/bulb/jam nut should not require any sealant as the adapter is pipe thread and the bulb seats on a shoulder within the adapter, much like a valve. If the threading on your sender hole is damaged you might consider repair or threading to the...

The physics of adding the calibration wire decreases the volume of the reservoir and thus reduces the volume of air required to displace the fluid into the sight tube. Generally speaking, this increases the reading on the sight tube. Whether or not your particular gauge will be accurate at empty...

It is pertinent to have a functional sending unit. Did you follow the calibration instructional pdf previously attached? You can also start with an empty tank and set your fluid level there. Most commonly, a small air leak will cause your issue. They are difficult to trace down, but you have a...

Apply air pressure and have a friend feel for air at the other end. You do not need special fittings to do so, just a rubber tipped air gun and steady grip. As for checking the system integrity, you'd have to hook everything up and see if the levels hold over time. www.morrisgauge.com

A little soap and water can go a long way. Often we find that once oil has saturated the dial face, there is little to do beyond warm soap and professional grade wax and grease remover. The paint becomes quite porous over time so anything that has absorbed goes deep. We also find on steel faces...

The sending unit is a 6 volt King Seeley points style, while the switch is just that. You can set up a mock system with the appropriate KS temp gauge (starts on HOT), when energized the pointer will move to the COLD hash mark with a pulse rate of approximately 1/second. As the temperature rises...

Are you looking to have the unit cosmetically restored or simply serviced? Many of those speedometers are available exchange since the cosmetic decal sets came out. I cannot speak to the work of others, but you may find that the trade out works for you. The pot metal frames of those speedometers...

Hello. We have a lovely restored gauge panel up for auction, but are always willing to end it for a forum member. Feel free to check it out and let us know if you have any questions. Thanks. http://www.ebay.com/itm/301708469323?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649