Search results

I posted this yesterday just as the site was closing so hope it doesn't appear twice, Further to Jim's comments, here is an example from the June 1928 Canadian Parts Price Book that shows some parts designated as "AR". Note how #2084-AR mentions that it is for the first 500 Canadian cars. This...

I made a little switch panel that mounts under the dash rail, attached to existing bolts. I can send you a sketch if needed. I mounted a fuse block on the firewall so its out of the way but easily accessable.

I installed mine a few years ago but it the chassis was bare. Looking at it now there seems to be lots of room to drill from the outside. I think you also have to enlarge the hole for the shaft housing to fit through. You can find more information here...

I have found velcro works well to hold door panels in place, so you can easily remove them if need be. Staple one side to the wood frame and glue the other side.

Not sure if its the same, but for my Model A I pushed a short piece of plastic straw over the shaft, pinched the end then it was easy to line up with the hole. Pull hard on the straw while pushing the handle and the shaft will slide in.

If it's what I think you need (A47301F in my old Mac's catalogue), how about this: take some thinwall aluminum tubing, run it through some rollers to squish it almost flat, then cut a slit down the middle of the top side. Drill and nail as needed then close up the seam like you would with the...

I just went through the same issue when I wanted to use up some PPG DAR acrylic enamel but the recommended hardener is no longer made. I found some ProForm 2.1 VOC Universal Urethane Hardener (it may be called something different in USA) and it worked well with the enamel and also with PPG JTX...

The upper brake light part of one of mine failed as well after about 1 year of use. I confirmed it wasn't a wiring problem so just bought a replacement lens. It has been working fine ever since. Mine is a 12 volt system. It happens sometimes with electronics.

I found a white paper published by SEMA regarding the use of radial tires on classic vehicle rims. It doesn't address the use of tubes but does caution about the increased possibility of stress fractures. i would imagine that the higher bulging of the radials might also tend to push it away from...

Modern rims have an extra bead that helps seal and hold the tire in place. Note how they pop in place when inflated. I think its a safety issue. For that reason I put tubes in my radials on 16" wires. My only worry is that a nail might cause a sudden deflation rather than a slow leak.

What's the deal with MAFCA sending renewal notices in August? Are they getting short of funds? By the time we in Canada pay a $10 premium(covers mailing), credit card fees at source, foreign transaction fees, 40% exchange it gets up close to $100. Paying by cheque saves a little.

Have you tried to contact PPG Refinish to ask for a local supplier in your area? I have been able to get as little as 1/2 pint mixed by my supplier when I was trying to match a Ford blue, it was about $30, but hardener and reducer is extra. They may be able to put it in a spray can for you, as...

Here is what I use. Simple, quick, accurate as any, no need to roll car forward or back, best of all cheap - made with scrap wood. It makes virtually no difference how high you measure. Picture two flat vertical wooden boards pointed slightly in. Measure between them front and back. Up or down...

It would probably be similar to a Model A sedan so try Classtique Upholstery who make Model A kits but also seĺl fabric by the yard.

Jay Jay, if you run a separate parallel power feed to the cowl lights, the tail lights will not come on as they are on a separate circuit from the light switch. I mounted a toggle switch with an LED indicator on my steering column using a little L-bracket. I have bright white LED's in my cowl...

That's a standard Ford 3-wire solenoid. The metal part on the end should be grounded. It looks like somebody trimmed the mounting bracket off - it is normally mounted on the firewall, which provides the ground. Power goes from the starter switch to the small terminal then to ground. From your...

Are you looking for something like a speedi sleeve for the the area where the grease seal goes?

Just installed and set set it up. Haven't tried it yet but it looks impressive. I was happy to see an option for speed in km/hr, but one thing I noticed is that we in Canada measure fuel economy in litres/100 km rather than km/liter. I think most other metric countries are the same.

A while ago I was looking to add a hitch to my trailer for a bike rack and found you can get adjustable width universal receivers from places like etrailer.com or Amazon. All you might have to do is fabricate some end brackets to attach to the frame.

Don't understand how you can use a dual filament bulb in a single base cowl lamp holder, but try here: https://www.ledlight.com/6-volt-positive-ground-automotive-led-lights.aspx btw, I used bright 240 lumen LED's in my cowl lamps and have them wired to a separate switch to use as daytime...