Search results

Thanks for the responses, I had considered that the tube was for a south wind heater. Yes, that is a 81 model 92 carb, with 7/8" venturis. Picked these up an an auction of random garage stuff.

Picked up 3 carbs today, hoping to get a couple spare cores for my Dads 8BA hot rod pickup. I’m pretty new to this so go easy on me. Haha. What is the tube on this 94? Is this for the weird vacuum advance? All the 94s are basically the same? 59a / EAB / 21-29/ 91-99 etc ?? Also picked up a...

Im going to check on those H10's, some ones i see are one piece, no screw top. Thanks for the responses!

Hi fellas, 8BA flathead , I am looking for a spark plug with the screw on top so that I can the old style braided looking wires with a ring terminal. NGK B6L? any others? Thanks Mark

still for sale

Thank you for the responses. If i spin it with a drill , I get less than 1 volt output. If i put a jumper wire between the Field and the Output , and spin it with a drill i get 9 - 10 volts.

My dad’s flathead. Generator question. i was checking to see if the generator will motor. If I put 12v to the output /armature, and connect the negative to the case , I just get a spark. If I connect a jumper from the field terminal to the output/armature, and put 12v to the armature it...

Sold. Thanks. I don’t see how to delete

My dad’s stuff. I assume these are wheel Puller tools. For a T ? A? Both ? These tools are basically the same ? I will probably get rid of one of them Thanks

The pushrod i have now measures a little less than 8" (7-15/16) Thank you for your responses. General question, does the pump cam come up at a certain degree of crank rotation? (like TDC or BDC??) Right now this is the intake i have, My dad did have this running at one time with this...

Thank you for the responses. Correct, I believe my Dad bought an early style fuel pump stand with breather cap so he could add oil. Do they make a long and short fuel pump pushrod? I can also fabricate a spacer to make up the difference. The PCV / breather system was also something we...

Hey fellas, I am trying to get my late Dads hot rod pickup back together. Its an 8BA with an aftermarket intake (Hexagon). Intake looks like it was designed to fit many years by the number of bolt holes, lack of road draft tube, etc. Can you educate me on the fuel pump and pushrod? How...

New valves for model A. 9 total. 4 stainless and 5 steel. And 8 keepers. Cleaning out some of Dads stuff I will probably not use. $40. I can get a shipping cost if interested. Shouldn’t be too much

32 Ford Wishbone. 47 1/2 " from center ball to the spring perch. good solid condition. no rot, no holes. pivot ball has some rust but no wear. see pics. pickup only New Haven CT. $250

looks like 47 1/2" if i measure from the center of the ball down 1 leg of the wishbone to the center of the perch hole. Is this correct? If so i would like to see it not cut up and used on a 32 if needed.

Thank you for the info! Hopefully I have some to get it in this week

Hey Fellas , I am replacing the pan gasket on my late Dads half finished hot rod (I suppose i should post more about that). Looking for some tips especially on the white rope end seals. Soak them in oil? motor oil? sealant on the corners? a little grease on the cork gaskets to hold them...

For Sale my dad’s 27 Tudor. Running and driving registered car in CT. Survivor car. Original interior and body. Engine number matches chassis. Mechanically very good. Recent windshield , door glass , aluminum pistons , wood bands, tires etc. very old paint. Very solid body. SALE...

FelPro 7013 head gasket, it is stamped R2 version. copper clad gray core new, a little "shelf wear" $25 plus a few bucks shipping

We werent able to bring a car this year but Dad and I enjoyed the event once again. Any tally on the total number of cars ??? must have been 60 + ? The town cars were beautiful, and the 'survivor' Town car was also there, I have seen up there before.