Search results

After re-installing the convertible frame mechanism, one side is hitting the interior trim cover; that covers the rear seating area. This is only hitting on one side. I'm using new cylinders, new springs, and a new pump. There isn't any air in the system. How can I adjust this frame...

I have a 1942-1948 Ford/Mercury Convertible front bench seat that I bought on ebay with the bottom cushion and two backrests that are upholstered (although the upholstery needs to be redone but not in terrible condition). This also has a good frame and functioning sliders. The backrests also...

Looking to buy 1942-48 Ford/Mercury Convertible Front and Rear Seats. The rear seats are unique to Convertible models. Only the front seats can be from 2 Door Sedans please. I'm looking for a front bench seat with working sliders. The rear seats do not slide and are stationary. I'm located...

That was a good try. However, the x-height on the letter "F" is different and the letter "O" is quite a bit different as well. Thanks for the input though.

I agree that this looks like an Art Deco font; that was what I searched for first to no avail. I even tried using Identifont to no avail.

What is the Font Name for the non-script Block Letter 1941 Ford Emblems please? This lettering was used on the dash emblems on a few different models including the 1941 Super Deluxe vehicles. I have attached a photo showing this for reference. Thank you

For a 1946-1948 Ford and Mercury Convertible model, what is the sequence to reinstall the vent window assembly and the door glass assembly please? Is the sequence installing the vent window assembly first and then installing the door glass assembly second? Or do you install the door glass...

Are 1946-1948 Ford and Mercury lower door hinges adjustable? Or were these hinges screwed to the A pillars?

What is the order of installing the vent window assembly, window regulator, window frame, and quarter windows please? I'm using all new window glass runner channels. Which one is installed first, second, third, and fourth please? This is for a 1946-1948 Ford or Mercury convertible door glass...

I have a ford nos gas sender .1941 ford gas gauge would like to set sender arm to full and empty.E mail bhrstreet@gmail.com.

Where should the tensioner washers be positioned with the hood and hinge arm mechanism? A. Should the tensioner washers be used between the hood and the hinge arm? OR B. Should the tensioner washers be used on the shoulder of the bolt through the hinge arm then onto the hood bolt hole...

The body side trim has clips and studs. There are eight stud pieces that hold the trim onto the car. What location do the studs go when attaching the trim to the car? Meaning what combination do these studs go to the hood, the cowl, the doors, and the quarter panels? Do each of these...

Where do the bolts go on the belt line trim on a convertible.

I'm still looking for these. Thank you

Hi, I would like to purchase two 46-48 Ford/Mercury Convertible Top Tensioner Springs in New or NOS condition. These connect from the convertible top mechanism to the floor pan bracket. These are approximately 18.5 inches long. Thank you

I have bob drake quarter window front edge seal. i can't figure them out to install the seal. Part #21A-7630106.:confused:

I have the Bob Drake quarter window front edge seal. I can't figure out how to install the seal. Part #21A-7630106.:confused:

I'm looking for information on how to replace the glass in convertible quarter windows for a 1948 Mercury Convertible. The quarter window frames are already out of my car. I do not see any screws in the frame; so I cannot figure out how to separate the frame from the glass. Thank you for...

I'm looking for the one for the door post. Thanks

My stock 1949 courtesy light switch does not work. Do you know of any courtesy switches that will work or that can be retrofitted to work with this housing. This is for the B Pillar light switch. I cannot find a NOS switch. Thank you for your help.