Search results

I believe that your speedo needs to be recalibrated. The part that the cable goes into and is driven by the cable which is magnetized, which in turn pulls the "speed cup"to move the needle to the correct speed. Over time the magnet becomes demagnetized and doesnt pull the speed cup enough. Take...

I'm not even sure that delux fenders will fit on a standard. I have a 1938 standard 2 door sedan and have "eyeballed" delux vs standard fenders and don't think they will fit. Besides, look at the lines of the standard fenders and, to me anyway, they are more attractive than the delux, jmo.

I used a 6v starter in my 12v converted 38 Tudor till it burned up. Took it to my local starter, gen. Alt. Repair shop. They put 12v guts in the same case, cost about $80.00 and has been working great ever since.

The only way you can tell which engine you have (FE engine) is to put number one piston on top dead center. Remove spark plugs number one and number four. Get a long piece of coat hanger, small welding rod, small dia. Wooden dowel. Ect. Put the rod down number one and make a mark that you can...

I do have a ford distributor. It is a crab type that has a pertronix unit instead of points.

No, it wasn't doing any of that. I have 180 degree thermostats. When the temp got up to 180 degrees and the engine was fully warmed up it would act like it was running out of gas, would die and wouldn't restart till the engine was cool again. With the new coil I drove it on the interstate and it...

I believe that I had covered all the things that should have fixed the vapor lock. So I didn't think I had vapor lock. On the other hand the coil in the car was unknown and it was chrome. I have pertronix so I got a new pertronix coil to fit. Now there is no symptoms of vapor lock or anything...

ive had vapor lock problems ever since I bought my '38 Standard. Rebuilt radiator with modern core, bigger electric fan with shroud. New improved thermostats ect. ect. Car has pertronix, coil type unknown. I bought a new coil from pertronix and guess what? I drove the car about 100 miles today...

How about "Flim-flam man" with George C. Scott. There's lots of different makes of cars and trucks and if you look real close you will see a yellow and white 1960 Ford Starliner. Great movie also.

I've been into old cars since about 1966. Back then the main parts source was swap meets, the odd dealer find, maybe a buddy found a part, Hemings motor news where all the sellers thought their stuff was gold. Just couldn't find much for the old flatheads. No problems with crown Victoria's but...

I haven't checked the coil and it has a pertronix ignition.

I've used MMO, Seafoam, some type F auto. Trans fluid. None of that works

Yes, I do have a spacer. Have Bob Drake water pumps that were on the car when I got it. I use 100 percent gas here in Oklahoma. I quit using clothes pins about 1965. I do have a hand held thermometer but forgot to use it. I know that I should get an electric fuel pump but have been trying to put...

i have a '38 standard w/ '48 engine stock but with Offy heads and 4bbl. Intake. Since I've had this car I have had the radiator rebuilt, 4 core. Have electric fan with surround, Schumann 180 thermostats, overflow tank. 7 pound cap. It still vapor locks. Could it be a weak fuel pump? What else...

The passage that allows oil to reach the OD part of the trans maybe blocked causing the noise you hear. My T-85/R11 has a fill plug to add oil to the OD. Try that.

I don't know about brass but most all the suppliers have those disconnectors. I don't like that type of disconnect because they sometimes don't make good contact. I like the switch with an on/off knob. You can get them at the same places.

There are some of them on eBay right now, sold I believe by So Cal. The ad said they are French made.

What is recommended with POR 15 is to put a good coat of your favorite primer over the stillwet or at least tacky por 15. Has to at least be tacky or it won't stick. Then you can paint over the primer whenever you want. If you try to paint over dry por15 it won't stick. It is great stuff.

There is an ad on eBay that says it is a 38 gauge cluster. It is not the same as mine. It has no larger stripe and the three smaller stripes aren't the same. I guess I'll stick with what I have.

My speedo looks like yours but the guage cluster has a red or brown (color blind) stripe around the center like the speedo and also three very small stripes around the edge which I don't see on yours. The speedo is lighter than yours but the stripes are bright. Go figure.