Search results

Great job. I like the new look!

If you reversed the polarity of the LEDs, they tend to burn out quickly. The original Model A's wiring to the tail lights are green for the yellow stop portion of the tail light and black is for the red running lights. Check that you have voltage on the black wire from the A's wiring to the...

Dac send me your email and I will send you a list of all the bulbs for both 6V and 12V. My email is jrelliott42@gmail.com.

Check the grounding of the lights.

Joe K is correct about all the connections. I removed the connector between head light shell and the flexible connector and replaced with bullet connectors on both ends of the wires going from the bulbs to headlight wiring harness. I also threaded a separate ground wire from each headlight...

Lot easier to change the starter on a Model A than a Corvair.

My neighbor, Dick Headmon, is repairing a '31 Chevy 4-door which had a bad gas tank that is original in every way. The Chevy is a much nicer than the '31 Ford. The engine has never been overhauled and still runs very smooth. Now understand Ford had to get the V-8 in production soon as other...

When I have a short like when you first described the problem, I attach a voltage appropriate bulb (6V or 12V) across where the fuse goes. Made the bulb attachment with wires (about 6" long) attached to alligator clips that will connect to the terminals of the fuse and to the bulb base and...

I am '83. Good to see so many about my age. Hope all the rest are in good health. Still walk about 3 miles most days of the week and trout streams as much as possible.

I have part numbers for the front and rear bearings on the Powerhouse. Front *** 6204.2RSR.C3, Dayton #1ZGH4, NTN 6204LLBC3/L627 Bore 20mm Outside dia. 47mm width 14mm. Rear *** 6203.2RSR.C3, Dayton #1ZGH3, NTN 6203LLBC3/L627, Grainger 6205 Bore 17mm Outside dia. 40mm width 12mm

Have one on my '28 Blindback. The generator was very well made. When I rebuilt mine, the bearings still had grease in them. Did replace both bearings before reassembling. The only problem with these generators is the material holding the brushes likes to break easily, and no replacements.

Should turn freely with little drag. Check the bearings. When was the last time the rear bearing was oiled if not a powerhouse? If it is a powerhouse generator, both the front and rear bearings are sealed bearings. If it is a powerhouse, I have the part numbers for the bearings. Front...

Riveted electrical contacts are a real PIA. A neighbor has a '63 Thunderbird that the sequential tail lights would not work. The contact that carried the current to the tail lights had corroded inside the connection even though the connection looked good. Soldered the two pieces together and...

Marvel Mystery oil in gas makes the valve turn easier. Just my own experience.

When you make the hole for the bracket to go through the cowl panel, use a Greenlee chassis punch and paint over the raw metal of the hole. The chassis punch will make a very clean hole and not mess up the surrounding paint. If the rubber grommet was not included, or if it is old and brittle...

Are you using separate lights for your turn signals in the front and the rear? If separate lights check the the ground connection. It must be good for the lights to work properly. Those blue connectors are not very reliable. I prefer good soldered connections sealed with heat shrink tubing...

I had vapor locks here in AZ at 5500 ft in elevation. Cured it by placing a 1/4" phenolic spacer between the carburetor and intake manifold. Fuel was getting to the carb, but boiling in the carb. Timing was set correct, new radiator, engine pans, and inside of engine is clean as no rust...

If the A was changed to Negative ground, and the generator polarized that way, then continue to run the A that way. It will run just fine. On disconnecting the load from the generator you can damage the generator. The Powerhouse generator is much better than the later models and the roller...

How do you get in touch with Mike Hill to see if he makes one for a Power House generator negative ground and 12V.

Looks like fun sledding behind a vehicle! Glad I grew up when I did as I could do a lot things that you cannot do today and survived. Go down to the creek with a .22 across the handle bars of my bicycle, go fishing, have real fireworks, purchase shells for shotgun and rifle without being 18...