Search results

Still looking, anyone have one?

Bump up. Still looking

Sold. Thanks

Selling a brand new 1930-31 ford coupe wood header. Bought brand new at Brattons for $135. Selling for $90 cant load pics on here. Email or text me for pics Kontinu1@comcast.net 6092009916 Thanks Josh

Looking for an Evans model A or B 4cylinder banger dual carb intake manifold. Thanks

If i had the pistons cut so they were flush with the top of the block and ran a copper gasket which is .080. Then ran that with the winfield head thats .080 clearance between top of piston and head. If i left piston alone (.055 above block) and just ordered a .125 copper gasket that would leave...

I recently got a winfield head 6.8:1. There is no relief cut for the piston and my piston comes up about .055 above the block. The gasket i have is only .60 and thats not compressed yet so much know this isnt going to work. I used a copper felpro 7013 previously and after i took that off its...

Well after the new copper gasket and the copper coat spray it seems ok. I warmed up the engine at idle let cool and retorqued. Then today I drove about 5 miles and still see no coolant leaking. Ill retorque tomorrow after it's cooled down. I'll leave the high compression head at 55ft lbs and...

Ok, I was going to let it warm up then retorque. I usually get a good 1/4 to 1/2 turn more out of it when it's hot. Then retorque it a few other times afterwards. Cold and hot. We'll see tomorrow how it holds up. I did take all the head bolts out last time and clean all the studs free of any...

Ok, I went with the copper gasket and a ton of permatex copper spray. It's had coolant in it for about 4 hours and so far no leaks. I'm going to give it until tomorrow to sit. I torqued the high compression head to 55 ft pounds following the correct tightening sequence. I torqued 20lbs, 35lbs...

We'll I have got nothing but problems. I retorqued I'm the morning then drive around town for about 9 miles. "Highlight of my day, had a nice cruise". Well when I got home I noticed coolant still seeping through the head but even worse my new aluminum radiator cracked along the bottom weld for...

The block was surfaced in the rebuild. I think the block isn't the problem due to first head sealing ok, and he used a copper gasket.

All good info, ill retorque it a few times and see it it stops. If not I'll try the stop leak. I really don't want to drain it and take the head off again. Do you guys always torque when cold or when it's hot??

The stock head on the rebuilt engine didn't seep but it was cracked. I did follow the directions on letting it warm up. I put the head on yesterday torqued. Put coolant in it today then warmed up the engine for 20 min. Shortly after it started seeping after it was turned off. I will now wait...

The first time I used the new head and gasket I used no rtv, just gasket only

Hi, I got a problem with the new high compression 5.5 to 1 head. I recently had my engine fully rebuilt. When I got the engine back put coolant in it and warmed up the engine. Within a few minutes I had coolant coming out of the side of the head, long story short I pulled it back off and it must...

Sold, thanks

I'm going to use the non detergent and follow what the builder says to do. Obviously I would like to use newer oil with all the added benefits it comes with. After it's been on the road and I know all is good with the rebuild in due time I'll probably switch to a newer style oil. For now I'll...

Don't know what warranty they give? If anything is wrong with it it's going back. If it starts leaking oil out the back of it, it's going back. That's why I took it there in the first place. I didn't spend that much to have it run rough, leak oil, smoke or anything. I've talked to other engine...

As far as I know it's all done in house. Someone from this site recommended him to me for rebuilding the model a engine. He has done others and also had two others redone in his shop waiting to be picked up. What if I use non detergent and added extra zinc?