Search results

  1. A

    Modify original Model A oil pump for Burtz engine

    Who can modify an original Model A oil pump for Burtz engine? Arlyn Bieber, San Diego
  2. A

    Model A powder pigment "apple green"

    Finished powder coating my Model A wheels "apple green" and have enough powder left over for a couple sets of wheels. $80 Arlyn Bieber anbieb@san.rr.com
  3. A

    original front seats

    Pair of original front "bucket" seats for Model A Tudor. Upholstery in excellent condition but not original. $75 for pair plus UPS charges. anbieb@san.rr.com San Diego, CA
  4. A

    Burtz engine oil pump

    According to Burtz engine Builders Guide---- A stock Model A oil pump with close fitting gears has been found to provide more than adequate volume and a relief valve is needed etc. Has anyone tried using a stock Model A oil pump on the Burtz engine and will it provide about 25psi at 50 MPH...
  5. A

    Victoria rear window shade

    Need an original rear window shade roller for Victoria, 26 inches long. Also rear assist straps used to assist when you exit the rear seat area. Thanks Arlyn Bieber
  6. A

    Victoria front seats, either early of late ones

    Need original front seats for Victoria, condition of upholstery is not an issue. Can be the early or late seats. Thanks, Arlyn Bieber, anbieb@san.rr.com or 858-530-2336
  7. A

    Victoria sun visor bracket

    Wanted Victoria or slant window sedan inside sun visor bracket. Arlyn Bieber anbieb@san.rr.com
  8. A

    Right side spare tire plate

    Looking for an original right side spare tire plate used to hold the spare tire in the fender. An original will have a "R" stamped in the plate. anbieb@ san.rr.com
  9. A

    Rear Main Thrust Face

    Larry is right. I have built more babbit engines than I can remember. Anything you do is a band aid at this point. The engine babbit is worn out, Do it right and replace the babbit, machine and balance the crank.
  10. A

    Original Robe rail Material-'31 sedans

    Have an original with end caps for sale. Any interest? Arlyn Bieber, San Diego
  11. A

    Do I panic? - Rear main oil leak.

    Is it leaking a 1" puddle or a 6" puddle? If a 1" puddle, that is normal. If a 6"puddle and it happened suddenly and is coming from the rear of the engine, the rear main babbit bearing has probably cratered and you need an engine rebuilt.
  12. A

    Early 1930 coupe electric windshield wiper

    Need an original electric windshield wiper for an early 1930 Model A Coupe. Arlyn Bieber, anbieb@san.rr.com
  13. A

    30-31 Coupe wooden header

    Need a new 30-31 wood header (above windshield). Checked all the suppliers and none are available until June. Arlyn Bieber
  14. A

    Radius rod rubber ball replacement.

    The rubber ball is designed for the V-8 not Model A. Don't mess with Henry's design, install the original.
  15. A

    Front End Rebuild Questions

    Don't forget to straighten the axle, it is the foundation for all the other work you are doing. It has been my experience after rebuilding over 100 front ends that 99% of the axles are bent. I also suggest you replace the king pin bushings. They may feel "tight" but I bet there is some wear...
  16. A

    AA speedometer driven gear needed

    Need to purchase a good condition AA speedometer driven gear Part # AA17271-F (6.6-11). The AA truck is an early 1930 short bed. The gear has 17 teeth and is slotted for the oval speedometer cable. The gear is stamped on the head 6.6-11. Arlyn Bieber, San Diego email anbieb@san.rr.com or call...
  17. A

    two Ford assembly plants...

    I would pick KC because it is likely my 1930 Coupe was "born" there. I was born in Kansas and rode home from the hospital in that very same Coupe in 1939. That Coupe resides in my garage and is in better shape than I am!!!
  18. A

    V/8 Clutch Pressure plate

    WANTED-- ORIGINAL 35-42 Ford 09A-7563 rebuildable clutch pressure plate with adjustable fingers and centrifugal flyweights ANBIEB@SAN.RR.COM
  19. A

    Starter drive shaft end play

    Anyone know the Ford specification for starter shaft end play? Just received a rebuilt starter and the end play is 0.120" or nearly 1/8". Seems like a lot to me. Snyder's list two thrust washer thickness, looks like the rebuilder should have used both. Can't find anything in the service...
  20. A

    Water leak in cylinder

    Have an Model A engine that developed a pin hole half way down number 3 cylinder. Bored the cylinder and installed a sleeve thinking that would stop the water leak but now when I air test the water jacket I get bubbles between the sleeve and the block both at the top and bottom of the sleeve...
Back
Top