Search results

Just had my 54 done at a local shop who is an old car guy. He had no trouble and said he knows how to set them up for radial tires. Needed a few shims but no parts.

Thanks for saving the old Fordbarn Ryan!

A back up electric fuel pump located on the frame rail near the tank that can be switched on and off when needed. The 6V Carter can allow the mechanical pump to draw fuel through it even when off. It must just be insulated from the frame to run on positive ground.

IIRC there is a weep hole to allow fuel to exit the pump housing if the diaphragm is bad, so its less likely to pump into the crankcase.

Haha, I'm not brave enough to do that. Of course, I should have done it while the motor was out and disassembled, if I'd been paying attention.

Hi all, I have another dumb question. My 292 has 57 G heads, but is in a stock 6v 54 Customline. The 12v sending unit standard in 57 is of course a different thread size and function than the older 6v sending unit. The gauge starts pegged at H but moves backwards to C as the engine heats up. No...

The only problem I noticed in my 1954 Customline when I swapped the 292 in was I couldn't use the thicker harmonic balancer. My machinist balanced it anyway and I just used it with the 239 pulley and timing cover to look original.

Thanks, I live on gravel roads so I'll make a cover. Funny story, I bought the car from the automatic transmission instructor at Denver Auto and Diesel College. So I assumed it was good, Its the only MX I have that doesn't leak. Not a drop. Wife's 65 TBird needs a drip pan, both my 69 Fords...

Yeah, just that lower cover plate. I can probably fab one, I was just hoping I wasn't damaging the torque converter or input shaft thrust bearing or anything. I swapped a 57 292 for the original 239 and everything bolted right up.

Did the 54 air cooled Fordamatic have a block plate between the bell housing and engine block? It was ten years between teardown and reassembly. I've searched my parts bins and can't find the lower access plate for the front of the torque converter. I have the small lower access plate with two...

That's what my machinist said to do. The tin sleeves were already removed from mine and he said they usually just bored them to 239 after that.

Then and now has a good selection. My 54 Y-block has the sediment bowl on top and the dual diaphragm for wipers. https://www.then-now-auto.com/product-category/fuel-pump-kits/ford-fuel-pump-kits/

"Also be wary of CHI-CON SLOPPY-COPY PARTS." Yes! After reading all the mechanical fuel pump threads, I did rebuild mine with the kit from Then and Now, I have a spare 54 Y-block pump and perhaps will make a picture thread detailing the disassembly and reassembly. Its not difficult, but a few...

I tried to post a video https://i.imgur.com/QOz4DsB.mp4

I've been working on this for a few months. Flatheads were notorious for overheating apparently. I assumed it was the block soaking up heat from the exhaust passages running through the water jackets, I installed an electric inline pump near the tank that I switch on to prime the mechanical pump...

Finally got this project on the road. I picked up the rusty little survivor in 2012, when you could still find running projects on CL for $1000. I had a line on a 292 core and it bolted right in place of the 239. I bought it from the automatic transmission instructor at Denver Auto and Diesel...

Thats the way to go haha. I may do that for a round body Falcon when I need to. I've roped in my 69 Cougar back glass twice with the butyl around the opening and it still leaks. But with a black vinyl interior, its not as obvious if I make a mess.

I've been putting off roping in my back window in my 54 Customline sedan after finding all the chrome trim and polishing it. The Carpenter directions say to install it dry. But the 54 shop manual says to put sealant ("rubber cement") between the glass and gasket. There was no sealant between...

I found Waldrons online, and they have the entire system. Thanks I guess Macs doesn't carry 54 stuff now. I should have gotten this car back together sooner, thankfully I got the headliner and back light seal already. Now I just have to polish up and sort all the stainless trim, uggh

Hi all. Trying to get a project off the backburner and I guess I've been in a cave. Got a fresh 292 in a stock 54 Customline sedan ten years ago. It still has single exhaust with crossover pipe and I figured it would be easy to find. I guess nothing is easy now. I've searched and can't seem to...